background image

 

IDX-OM-W019 

                        Air dryer

                                     

        

   

4. Checks and Maintenance

 

 

 

 

4 - 1 

 

 

 
 

4.1     Daily Check Points 

Check the following points during normal operation. If you find any problems, immediately stop the operation 
and refer to “Chapter 5 Troubleshooting”. 

- There is no air leakage. 

- The running lamp is on during operation. 

- Moisture (condensate fluid) is being discharged from the drain tube. 

- The pointer of the evaporation thermometer indicates in the green zone when it is running with 

pressurized air supply. 

- The pointer of the evaporation thermometer indicates about 3 to 10

o

C lower than the ambient 

temperature when the equipment is suspended with no pressurized air supply. 

- There is no abnormal sound or vibration coming from the equipment. 

- There are no abnormal smell or smoke coming from the equipment. 

 

4.2     Daily Check Points 
    4-2-1      Cleaning of ventilation grille(suction grille)

 

Clean dust and other foreign particles from the ventilation area with vacuum cleaner or air blow nozzle once a  

month. 

Caution 

During air blowing, put on protective glass and mask to prevent dusts from coming into 
throat or eyes. 

 
    

 4-2-2     Service parts

 

It is recommended to replace the following parts regularly. The interval alues shown in this operation 

 manual depend on the operating conditions (ambient temperature, installation environment, etc.),  
so  that they are for reference. 

 

Table 1.

 

 List of parts to be replaced regularly 

 
 
 
 

 

 

*Note

If it is mounted by option ”T” (With terminal block for power supply , run , alarm signal  and remote 

operation) or special order.  

 

 

    

4-2-3     Auto drain strainer

  

         Remove the dust deposited in the auto drain bowl assembly every month. Use neutral detergent for 

 cleaning. If the degree of dirt is heavy and operating failure still continues even after cleaning, replace 

the product. Also, shorten cleaning interval from next time. 

 

Description 

Recommended replacement period  *Note} 

Pressure switch 

One Million times. 

Fan motor 

20,000 hours 

Magnetic Contactor, Magnetic Switch 

One Million times. 

Checks and Maintenance 

4 

IDFB Series 

4.1 Daily Check Points 

Summary of Contents for IDFB11E-11




















































Reviews: