background image

 

QuickServer Start-Up Guide 

Page 31 of 32 

Appendix C.5. Specifications 

        

           

           

         

 

 

FS-QS-2XX0-XXXX 

2

 

Electrical Connections

 

One 3-pin Phoenix connector with:  RS-485/RS-232 (Tx+ / Rx- / gnd) 
One 3-pin Phoenix connector with:   RS-485 (Tx+ / Rx- / gnd) 
One 3-pin Phoenix connector with:   Power port (+ / - / Frame-gnd) 
One Ethernet 10/100 BaseT port 

Power Requirements 

Input Voltage:

 9-30VDC or 24VAC 

Current draw:

  24VAC 0.125A 

Max Power:

 3 Watts 

9-30VDC 0.25A @12VDC 

Approvals 

CE and FCC Class B & C Part 15, UL 60950, WEEE compliant,  
IC Canada, RoHS compliant 

Capacity Options 

FS-QS-20X0: 250 data points 

FS-QS-22X0: 3,000 data points 

FS-QS-23X0: 500 data points 

FS-QS-24X0: 5,000 data points 

Physical Dimensions 

4 x 1.1 x 2.7 in (10.16 x 2.8 x 6.8 cm) 

Weight 

0.4 lbs (0.2 Kg) 

Operating Temperature  

-20°C to 70°C (-4°F to158°F) 

Humidity 

10-95% RH non-condensing 

Figure 19: Specifications 

“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  

 

This device may not cause harmful interference 

 

This  device  must  accept  any  interference  received,  including  interference  that  may  cause 
undesired operation. 

NOTE:

 This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be 
required to correct the interference at his expense. Modifications not expressly approved by FieldServer 
could void the user's authority to operate 

the equipment under FCC rules.” 

 

                                                      

2

 

Specifications subject to change without notice.

 

Summary of Contents for FieldServer FS-QS-2XX0

































Reviews: