SMC Networks FAS-200 User Manual Download Page 51

Page: 51 / 98

FLEXIBLE ASSEMBLY SYSTEM

FAS200

User Manual for FAS200

- 49 -

Figure 54: Material detection

position.

TECHNICAL DATA

Dimensions:

Table of slotted aluminium section, 450 x 582 mm. Height 900 mm.

Air treatment unit:

Filter to 5 µm, pressure regulator and pressure gauge.

Pushbutton control:

Start, stop, reset pushbuttons. Emergency stop button, main switch on/off,

mode selector (auto-man), no material indicator and error pilot indicator.

Composition of station modules:

Index plate

Actuators:

- Pusher cylinder: Compact double-acting cylinder Ø25, Stroke: 40mm

(CDQ2B25-40D), with flow regulators and initial position detector. Controlled by

5/2 way monostable solenoid valve.

- Locking cylinders: 2 Compact cylinders Ø16, Stroke: 10mm (CQ2B16-10D).

Controlled by 5/2 way monostable solenoid valve.

Sensors:

- Reed type magnetic detector (D-A73CL).

Shaft feeder

Magazine capacity: 17 shafts.

Summary of Contents for FAS-200



































































































Search results

Summary of Contents for FAS-200

Reviews:

Related manuals for FAS-200

Brands by name

Popular brands

SMC Networks FAS-200, User Manual

Search results

Summary of Contents for FAS-200

Reviews:

Related manuals for FAS-200

Brands by name

Popular brands