EX260-TFN20
Troubleshooting
Contacts
AUSTRIA
(43) 2262 62280
NETHERLANDS
(31) 20 531 8888
BELGIUM
(32) 3 355 1464
NORWAY
(47) 67 12 90 20
CZECH REP.
(420) 541 424 611
POLAND
(48) 22 211 9600
DENMARK
(45) 7025 2900
PORTUGAL
(351) 21 471 1880
FINLAND
(358) 207 513513
SLOVAKIA
(421) 2 444 56725
FRANCE
(33) 1 6476 1000
SLOVENIA
(386) 73 885 412
GERMANY
(49) 6103 4020
SPAIN
(34) 945 184 100
GREECE
(30) 210 271 7265
SWEDEN
(46) 8 603 1200
HUNGARY
(36) 23 511 390
SWITZERLAND
(41) 52 396 3131
IRELAND
(353) 1 403 9000
UNITED KINGDOM
(44) 1908 563888
ITALY
(39) 02 92711
URL http://www.smcworld.com (Global) http://www.smceu.com (Europe)
Specifications are subject to change without prior notice from the manufacturer.
© 2010 SMC Corporation All Rights Reserved.
LED indication
Technical documentation giving detailed troubleshooting information can be
found on the SMC website (URL http://www.smcworld.com)
Setting (Continued)
Terminator
A bus termination is required at both ends of the PROFIBUS DP bus
segment.
<EX260-SPR1/-SPR2/-SPR3/-SPR4>
The bus termination switch is built-in to EX260-SPR1/-SPR2
/-SPR3/-SPR4.
Switch it ON if the SI unit is at the end of the fieldbus segment.
Note: Factory default setting is OFF.
<EX260-SPR5/-SPR6/-SPR7/-SPR8>
EX260-SPR5/-SPR6/-SPR7/-SPR8 do not have a
built-in termination resistor.
Termination is required on the outside of the SI unit. A termination
switch built-in to the PROFIBUS DP D-sub connector may be used.
ON
OFF
GSD file
Configuration
In order to configure the SI unit in the PROFIBUS DP network, the
appropriate device master file (GSD file) for the SI unit will be required.
The current GSD file can be found on the SMC website
(URL http://www.smcworld.com)
EX260-SPR1/-SPR2
Part number
GSD file
Smc_1430.gsd
EX260-SPR3/-SPR4
Smc_1431.gsd
EX260-SPR5/-SPR6
Smc_1432.gsd
1
2
3
EX260-SPR7/-SPR8
Smc_1433.gsd
4
Output number assignment
The output number refers to the solenoid position on the manifold and
starts at zero.
Bit: 7
0
Bit: 7
0
Bit: 7
0
Bit: 7
0
0
1
2 4 6
3 5 7
8
9
16
17
30
31
28
29
6
4
6
4
1 3 5 7 1
1
5 7
Output No.
Output No.
Bit No.
Bit No.
Valve manifold
Solenoid on side A
Solenoid on side B
Side D
0: Solenoid valve: OFF
1: Solenoid valve: ON
Byte
0 Offset
Byte
1 Offset
Byte
2 Offset
Byte
3 Offset
(SI unit side)
2
0
0
0
16 outputs
type
32 outputs
type
Diagnostic information
The EX260 SI unit can support 8 bytes of diagnostic information,
6 bytes standard diagnostic information and 2 bytes SI unit-related
diagnostic information.
Diagnostic information can be requested by the DP master from the SI
unit, and such system fault states can be indicated by the SF LED.
Technical documentation giving detailed diagnostic information can be
found on the SMC website (URL http://www.smcworld.com)
SF
BF
PWR(V)
PWR
PWR(V)
LED
Description
Turns ON in green when load voltage for the valve is supplied
Turns OFF when load voltage for the valve is not supplied or
outside tolerance range (19 V or less)
PWR
Turns ON in green when SI unit operating voltage is supplied
SF
System fault
BF
BUS fault
OFF
BF status
Description
No fault. Communication connection to the
master is established
Red ON
SI unit can not detect a transmission rate and
the connection to the DP master has failed
Red flashing
SI unit has detected the transmission rate,
but is not addressed by the DP master
OFF
SF status
OFF
OFF
OFF
SI unit-related diasgnostic error is detected
(load power for the valve is not supplied or
outside tolerance range)
Red ON
SI unit PROFIBUS DP address outside range
Red flashing
The configuration data sent from the DP
master to the SI unit does not agree with the
SI unit configuration
Red ON
Red ON
Red ON
<Indication of communication status>
Specifications
Connected load: 24 VDC Solenoid valve with light and surge voltage
suppressor of 1.5 W or less (manufactured by SMC)
Current consumption of power supply for SI unit operation: 0.1 A max.
Ambient temperature for operation: -10 to 50 ℃
Ambient temperature for storage: -20 to 60 ℃
Pollution degree 2: (UL508)
Technical documentation giving detailed specifications can be found on the
SMC website (URL http://www.smcworld.com)
Technical documentation giving detailed outline dimensions can be found
on the SMC website (URL http://www.smcworld.com)
Technical documentation giving detailed accessories information can be
found on the SMC website (URL http://www.smcworld.com)
Outline Dimensions
Accessories
