SMC Networks CEU5, Operation Manual, Page: 41 / 45

Chapter 9: BCD Output
CEU5
*
B
-*
type only has BCD output function.
(1) BCD output connector : Half pitch D-sub connector
DX10M-36S (made by Hirose Denki)
(2) Applicable connector : DX30AM-36P (plug: made by Hirose Denki)
DX30M-36-CV (cover: made by Hirose Denki)
or commercial cable with connector on the market can be
used, if it is compatible as above.
Note: When connectors (plug and cover) and cables (separately ordered) with the above
mode number are wired, a crimping tool is necessary.
In addition, as applicable connectors and cables are available as ASS’Y,
please contact MISUMI Corporation directly.
SHPT-H-36-L(length): One side of cable is loosened.
SHPT-HH-36-L(length): BCD connectors (male) are mounted on both sides of cable.
(3) Pin allocation and output signals in detail
19 36
18 １
C o u nte r sid e con n ecto r
pin a lloca tio n
(D X 10 M -3 6 S )
Pin No. Signal Meaning Pin No. Signal Meaning
1 D0 Digit of 10
-2
Bit0
19 D12 Digit of 10
1
Bit0
2 D1 Digit of 10
-2
Bit1
20 D13 Digit of 10
1
Bit1
3 D2 Digit of 10
-2
Bit2
21 D14 Digit of 10
1
Bit2
4 D3 Digit of 10
-2
Bit3
22 D15 Digit of 10
1
Bit3
5 D4 Digit of 10
-１
Bit0
23 D16 Digit of 10
2
Bit0
6 D5 Digit of 10
-１
Bit1
24 D17 Digit of 10
2
Bit1
7 D6 Digit of 10
-１
Bit2
25 D18 Digit of 10
2
Bit2
8 D7 Digit of 10
-１
Bit3
26 D19 Digit of 10
2
Bit3
9 D8 Digit of 10
０
Bit0
27 D20 Digit of 10
3
Bit0
10 D9 Digit of 10
０
Bit1
28 D21 Digit of 10
3
Bit1
11 D10 Digit of 10
０
Bit2
29 D22 Digit of 10
3
Bit2
12 D11 Digit of 10
０
Bit3
30 D23 Digit of 10
3
Bit3
13 (+/-) Sign 31 N.C. Unused
14 DATA
VALID
Reading OK signal 32 N.C. Unused
15 N.C. Unused 33 N.C. Unused
16 COM Signal ground 34 COM Signal ground
17 N.C. Unused 35 N.C. Unused
18 COM Signal ground 36 COM Signal ground
The above output is displayed in the digit of 10
-2
to 10
3
when the counter is connected to SMC
CEP1 series (decimal point setting is ***. **). When it’s connected to CE1 series (point
setting is *****.*), output is displayed in the digit of 10
-1
to 10
4
and the first place of decimal
point is displayed in pin no., 1 to 4 (signal D0 to D3).
BCD output sending out is the same as a value shown in LCD. That is, output includes
pre-scale and offset conditions (“FFFFFF” is outputted for counter IC overflow).
Polarity symbols (+/-) of Pin number 13 are assigned as shown below.
Low level (0): +/ High level (1): -
－ ３９ －