background image

 

 

ROOF  ASSEMBLY 

SELECT: 

 

4 x 2.200 m Roof Sheets 

2 x 2.050 m Spouting 

4 x 1.100 m Barges 

1 x 2.050 m  Ridge Flashing 

1 x 2.020 m Ridge Beam 

2 x 0.200 m Jack Studs 

8 x 75mm Screws 

31 x 40mm Weatherseal Nails 

58 x Rivets 

 

IMPORTANT—FOR SHEDS WITH OPTIONAL CLEAR 

ROOF PANEL 

 

Assemble as below, making sure that the Clear Roof Sheets 
overlap the standard roof sheets on both sides.  
The Clear Roof Panel must be secured to the Top Plate and the 
Ridge Beam. Pre drill and fasten with the 40mm weatherseal 
nails provided.

.

 

STEP 1: 

 

 

Place the Ridge Beam on a level surface and use 2 x 75mm 
screws to secure the Jack Studs to the underside of the Ridge 
Beam, one at each end (

fig. 1

). 

 

 

Turn the Ridge Beam /Jack Stud assembly over and place it on 
the timber Top Plate in a central position.  

 

 

Secure with 2 x  75mm screws through the top of the Jack Studs 
into the Timber Top Plate (

fig. 2

). 

STEP 2: 

 

 

Position the first roof sheet with the centre slots over the 
middle of the Ridge Beam. Gently fold the roof sheet over 
the Ridge Beam so that the ends touch the front & back Top 
Plates.  

 

 

Repeat with second roof sheet. Ensure that slots in ends of 
sheets line up with each other.  

 

 

Rivet sheets together at overlaps ,one  rivet either side of the 
ridge beam (

fig. 3

).  

 

 

Repeat with remaining roof sheets 

11 

JACK STUD

 

TOP PLATE

 

RIDGE BEAM

 

fig. 1

 

fig. 2

 

SIDE 

WALL 

FRONT 

WALL 

BACK 

WALL 

SIDE 

WALL 

TOP 

BOTTOM 

RIDGE 

fig. 3

 

Summary of Contents for SS2020

















Reviews: