Smartgen HGM9120 User Manual Download Page 14

Page: 14 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 14 of 58

4.3 LCD DISPLAY

4.3.1 MAIN DISPLAY

Main screen shows pages; use

to scroll the pages and

to scroll the screen.

★

Status

, including as below,

Genset status, mains status, and switch close/open status

★

Engine

, including as below,

Speed, engine temperature, engine oil pressure, liquid (fuel) level, canopy temperature, oil

temperature, Configure Sensor 1, Configure Sensor 2, battery voltage, charger voltage,

accumulated run time, accumulated start times.

★

Gen

, including as below,

Phase voltage, Line voltage, frequency, phase sequence

★

Mains

, including as below

Phase voltage, Line voltage, frequency, phase sequence

★

Load

, including as below,

Current, each phase and total active power (positive and negative), each phase and total

reactive power (positive and negative), each phase and total apparent power, each phase

and average power factor (positive and negative), accumulated energy (

kWh, kvarh, kVAh

)

and earth current.

Note:

When only mains switch on indicator lights, count active and inactive power,

apparent power, power factor, but accumulate electric energy. Counting the generator active

and reactive power, apparent power, power factor, and accumulate electric energy under

other conditions.

NOTE:

Power factor shows as following,

Remark:

P stands for active power
Q stands for inactive power

Summary of Contents for HGM9120



























































Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands

Smartgen HGM9120, User Manual

Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands