background image

MyOT interface/actuator for OpenTherm Boilers 

User manual and data sheet

 

 

 

General Safety Rules 

 

Before using this device, certain precautions must be taken to reduce any risk of fire and/or personal injury:

 

1.  Read all instructions carefully and follow all precautions contained in this manual. All direct connections to the 

mains conductors must be made by trained and authorized technical personnel. 

2.  Pay attention to any danger indications placed on the device or contained in this manual highlighted with the 

symbol 

  . 

3.  Disconnect  the  device  from  the  power  supply  or  battery  charger  before  cleaning  it.  For  cleaning,  do  not  use 

detergents but only a damp cloth. 

4.  Do not use the device in gas saturated environments. 

5.  Do not place the device near heat sources. 

6.  Use only the original EcoDHOME accessories supplied by SmartDHOME. 

7.  Do  not  place  the  connection  and/or  power  cables  under  heavy  objects,  avoid  paths  near  sharp  or  abrasive 

objects, prevent people from walking on them. 

8.  Keep out of reach of children. 

9.  Do not carry out any maintenance on the device but always contact the assistance network. 

10.  Contact the service network if one or more of the following conditions occur on the product and/or an accessory 

(supplied or optional): 

a. 

If the product has come into contact with water or liquid substances. 

b. 

If the product has suffered obvious damage to the container. 

c. 

If the product does not provide performance conforming to its characteristics. 

d. 

If the product has undergone a noticeable degradation in performance. 

e. 

If the power cord is damaged. 

 

Note: 

In one or more of these conditions, do not attempt to make any repairs or adjustments not described in this manual. 

Improper interventions could damage the product and force additional work to regain the desired operation. 

 

WARNING! 

Any type of intervention by our technicians, which will be caused by an incorrectly performed installation or 

by a failure caused by the customer, will be quoted and will be charged to those who purchased the system. 

 

Provision for Waste Electrical and Electronic Equipment. (Applicable in the European Union and in other European 

countries with the separate collection system).

 

Summary of Contents for 01335-2080-00












Reviews: