SMART SE240 Installation And User Manual Download

Page: 7 / 100

About the SMART Hub SE240

About the SMART Hub SE240

The SMART Hub SE240 is a device you connect to SMART Board™ interactive whiteboards,
SMART Boards

for Flat-Panel Displays

, Actalyst™ interactive overlays and Sympodium™

interactive pen displays. It lets you to do the following with your SMART products without
connecting to a computer:

•

whiteboarding

•

collaborating with others using Bridgit™ conferencing software

•

viewing and working with computer or video source input on your SMART products’ displays

This chapter introduces you to the SMART Hub SE240 and presents its features.

•

SMART Hub SE240 Features

(this page)

•

SMART Hub SE240 Firmware Features

(page 2)

•

Standard Accessories

(page 2)

–

Power Supply

(page 2)

–

Cables and Adapters

(page 3)

SMART Hub SE240 Features

The SMART Hub SE240’s compact size allows you to integrate it into your boardroom or
classroom easily. You can mount the SMART Hub SE240 in four ways:

•

19" (48.3 cm) rack mounting

•

wall mounting

•

table top or shelf mounting

•

under-shelf mounting

The SMART Hub SE240 includes connectors for:

•

SMART products

•

speakers

•

up to two computers

•

up to two video sources

•

other peripheral devices (including USB storage devices)

Summary of Contents for SE240





































































































Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands

SMART SE240, Installation And User Manual

Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands