SMAR FRI303 Instruction Manual Download Page 28

Page: 28 / 36

FRI303 – Operation and Maintenance, Instruction Manual

4.2

Assembly Procedure

Refer to figure 4.1 –

FRI303

Exploded View.

•

Place the input boards into housing (

), ensuring all interconnecting pins are connected;

•

Place the display (

) into the housing, mounting it properly according to the desired viewing

position;

•

Tighten the fixing screws (

);

•

Fit the cover (

and

) and lock it using the locking screws (

Firmware Update Procedure

For firmware update of the

FRI303

equipment see

FDI302-1

manual, visit website Smar:

www.smar.com

Accessories

Main and I/O boards can be changed independently.

ACCESSORIES

ORDERING CODE

DESCRIPTION

PBI-PLUS

USB Interface for Profibus PA.

SYSCON

System Configuration Tool.

PS302

Power Supply.

BT302

Terminator.

FDI302-1

Fieldbus/PROFIBUS-PA Communication Interface for Firmware

Update.

DF47

Intrinsic Safety Barrier for Fieldbus.

Summary of Contents for FRI303





































Search results

Summary of Contents for FRI303

Reviews:

Related manuals for FRI303

Brands by name

Popular brands

SMAR FRI303, Instruction Manual

Search results

Summary of Contents for FRI303

Reviews:

Related manuals for FRI303

Brands by name

Popular brands