background image

Important Safety Instructions

SMA America, LLC

4

SC500U_GFDI-IUS101311

Installation Guide

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions for Sunny Central 500U PV inverter, that must be followed 
during installation and maintenance of the PV inverter.
The Sunny Central 500U is designed and tested according to international safety requirements, but 
as with all electrical and electronic equipment, certain precautions must be observed when installing 
and/or operating the Sunny Central 500U. To reduce the risk of personal injury and to ensure the 
safe installation and operation of the Sunny Central 500U, you must carefully read and follow all 
instructions, cautions and warnings in this installation guide.

Warnings in this document

A warning describes a hazard to equipment or personnel. It calls attention to a procedure or practice, 
which, if not correctly performed or adhered to, could result in damage to or destruction of part or all 
of the SMA equipment and/or other equipment connected to the SMA equipment or personal injury.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or 
serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or 
serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or 
moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

Summary of Contents for Sunny Central 500U





















Reviews: