SMA SUNNY BOY 4000TL Installation Manual Download Page 66

Page: 66 / 76

Messages

SMA

Technologie AG

SB40TL_50TL-IEN081211

Installation Guide

< Inst. code invalid >

The Inst. code (personal installer password)
entered is not valid.

•

Enter a valid Inst. code.

< Grid param. locked >

The current country data set is locked.

•

Enter a valid Inst. code to change
the country data set.

< Waiting for main system >

•

The DC voltage at the DC input is not
sufficient to operate the main
computer.

•

The selected rotary switch setting is
not assigned for the country
configuration.

•

The parameters to be changed are
protected.

•

Ensure that sufficient DC voltage is
available (green LED lights or
flashes).

•

Check the setting of the rotary
switch (see section 6.4.2).

•

Enter Inst. code.

Cause

Remedy

Summary of Contents for SUNNY BOY 4000TL













































































Search results

Summary of Contents for SUNNY BOY 4000TL

Reviews:

Related manuals for SUNNY BOY 4000TL

Brands by name

Popular brands

SMA SUNNY BOY 4000TL, Installation Manual

Search results

Summary of Contents for SUNNY BOY 4000TL

Reviews:

Related manuals for SUNNY BOY 4000TL

Brands by name

Popular brands