SMA STP3.0-3AV-40 Operating Manual Download Page 35

Page: 35 / 106

6 Electrical Connection

SMA Solar Technology AG

Operating manual

STP3-6-3AV-40-BE-en-13

3. Ensure that all conductors are correctly connected to the M12 plug.
4. Unscrew the protective cap from the jack for the

RS485 communication connection.

5. Plug the M12 connector into the jack for the RS485

communication connection and screw tight. When
doing so, align the connector so that the key on the
inverter AC jack is inserted into the keyway on the
plug.

6.5

Mounting the WLAN Antenna

Requirement:

☐ The WLAN antenna supplied must be used.

Procedure:

DANGER

Danger to life due to electric shock

• Disconnect the inverter from all voltage sources (see Section 9, page 69).

2. Remove the protective cap from the jack on the inverter.
3. Plug the WLAN antenna into the jack and screw

tight (torque: 1 Nm).

4. Pull on the WLAN antenna to ensure that the WLAN antenna is securely in place.

6.6

DC Connection

6.6.1

Requirements for the DC Connection

Connection options:

The inverter has two DC inputs, to each of which one string can be connected in normal operation.

Summary of Contents for STP3.0-3AV-40











































































































Search results

Summary of Contents for STP3.0-3AV-40

Reviews:

Related manuals for STP3.0-3AV-40

Brands by name

Popular brands

SMA STP3.0-3AV-40, Operating Manual

Search results

Summary of Contents for STP3.0-3AV-40

Reviews:

Related manuals for STP3.0-3AV-40

Brands by name

Popular brands