background image

Installation of the Sloan OPTIMA Plus EBF-615 or EBF-650 Battery Powered,
Sensor Operated Faucet makes wash-up totally “hands-free” providing the
ultimate in sanitary protection and automatic operation. The OPTIMA Plus faucet
uses infrared technology to sense the user’s presence and turn on a water supply
that has been pre-mixed to the desired water temperature. When the user’s
hands are removed from the invisible beam of  light, the water supply
automatically turns off. In addition, the faucet is powered by four “C” cell batteries
which eliminates the need to run any electrical lines to the system.

The Sloan EBF-615 or EBF-650 battery powered, sensor operated faucet comes

complete with an integral faucet and sensor assembly, control module, alkaline
batteries (Size C), and all mounting hardware. Back checks and a grid strainer
are also available as optional equipment. The installer should supply 3/8 inch
copper supply tube or flexible hose connections.

The following instructions serve as a guide when installing the Sloan EBF-615
or EBF-650 faucet. As always, good safety practices and care are recommended
when installing your new faucet. If further assistance is required, contact your
nearest Sloan  Representative office or  the  Sloan  Installation  Engineering
Department at 1-888-SLOAN-14.

EBF-650 I.I. — Rev. 1 (06/00)

Code No. 0816321

INSTALLATION INSTRUCTIONS

BATTERY POWERED

SENSOR OPERATED

LAVATORY FAUCETS

EBF-615
EBF-650
Battery Powered
Sensor Operated
Lavatory Faucets

Includes Instructions for
Installation of Optional
Back Checks

Made in the U.S.A.

ANSI/ASME A112.18.1M

LIMITED WARRANTY

Sloan Valve Company warrants its EBF-615 and EBF-650 Faucets to be made of first class materials, free from defects of material or workmanship under normal
use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three
years (1 year for decorative finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which
prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims
will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s
products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE
COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

EBF-615

EBF-650

Certified

Summary of Contents for Optima EBF-615











Reviews: