background image

Code No. 0816674

Rev. 3 (02/17)

INSTALLATION INSTRUCTIONS FOR OPTIMA

®

 SYSTEM SENSOR ACTIVATED 

SLOAN

®

 CONCEALED WITH TRUE MECHANICAL OVERRIDE FLUSHOMETERS

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship for a period of three (3) 
years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company will, at its option, repair, replace, or 
refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned 
to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s 
products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY 

CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

SENSOR LOCATION & POSITIONING IS 

CRITICAL!

Failure to properly position the electrical boxes 

to the plumbing rough-in will result in improper 

installation and impair product performance. 

All tradesmen (plumbers, electricians, tile 

setters, etc.) involved with the installation of 

this product must coordinate their work to 

assure proper product installation.

‡  POSITION OF SENSOR BOX CAN BE RAISED OR LOWERED 1” (25 mm) IF IN CONFLICT WITH 

HANDICAP GRAB BARS.

MODEL 152

MODEL 195

MODEL 152

MODEL 195

Concealed Closet Flushometers 

1-1/2” Rear Spud

•  Model 152 ES-S TMO

Concealed Urinal Flushometers 

3/4” Rear Spud

•  Model 195 ES-S TMO

ROUGH-IN

¾” 

(DN 20 mm)

IPS

SUPPLY

2¾”

(70 mm)

2”

(51 mm)

1½”

(38 mm)

L DIM. 2¾”

(70 mm) 

WALL 

THICKNESS

4¾”

(121 mm)

13½”

(343 mm)

Summary of Contents for 152 ES-S TMO SWB









Reviews: