Caution
Prohibition
Components
Pan Head
Options
This product is designed to withstand equip-
ment up to 5kgs. Please do not use equipment
exceeding this limit.
Equipment that can be used with this Tripod
Carrying the Tripod
Equipment with uneven weight distribution
should not be panned by the Quick Shoe.
A loose mounting screw may go unnoticed, and
result in a sudden accidental fall.
Carrying a tripod with a camera left on can
result in unexpected accidents. We therefore,
recommend that you remove your camera
when carrying the tripod.
R
Caution
Prohibition
Handle Connecting Screw
Panning Lock Knob
Vertical Tilt Handle
Locking Lever
Release Button
Detach Proof Groove
Pan & Tilt Handle
Dual Axis Bubble
Levels
Camera Platform
1/4" Camera Mounting Screw
G273-1
Pan Head
Quick Shoe
Center Column
Locking Collar
Main Body
Center Column Stopper
Center Column
Base Stopper
Leg Lock Lever
Soft Grip
Center Column
3-Position Leg Angle
Adjustment Locks
Leg
Leg Lock
Rubber Leg Tip
PRO 700DX Tripod
Operating Instructions
Thank you very much for choosing SLIK PRO 700DX Tripod.
The SLIK Corporation has designed your tripod to be a sturdy,
rugged, dependable product that will provide you with many years of
satisfactory use.
Please take a few moments to read this instruction sheet carefully
before use so that you can take full advantage of your Tripod's many
fine features.
Retain this instruction sheet in case you might want to refer back to it.
Caution
This caution icon refers to information pertaining to important safety
procedures in preventing injuries, or damages which may occur as a
result of mishandling this product.
Prohibition
This prohibited icon refers to information pertaining to prohibited con-
tents. Please refer to instructions closely to avoid accidents.
Specification
Length folded
760mm
(29 11/12")
Max. operating height 1,900mm
(74 5/6")
Max. center column ext. 380mm
(14 11/12")
Weight
3.53kg
(7lbs 13oz)
BALL HEAD 800
QUICK SHOE(U3/8")
Cat. No. 618-340
THREAD ADAPTER SET
Cat. No. 618-331
11mm
(5/12")
8mm
(1/3")
U3/8
U3/8
BALL HEAD 800
QUICK SHOE(U1/4")
Cat. No. 618-335
Caution
Soft Grip is consumption and cannot be used parmanently.
Please relace it whenever ragged.
Prohibition
The bolts of the Pan Head marked “ ” should not be adjusted nor operated.
Loosen the Center Column Stopper and the
Locking Collar, and then pull out the Center
Column.
Inverting the Center Column
Make sure to re-attach the Center Column
Base Stopper, in order to prevent the Center
Column from falling out.
By inverting the Center Column, it is possible to
do copy, and close up work.
Opening the Tripod Legs
Insert the Center Column from the lower side of
Main Body, and tighten the Locking Collar and
the Center Column Stopper.
Caution
Caution
How to change the Pan Head fixing screw
Printed in Thailand.
Care of the Tripod
OIL
THINNER
DO NOT apply any grease or oil to this product.
Clean with a mild detergent and a soft cloth only.
DO NOT use close to flame. Avoid extreme heat.
Always remove the Pan Head when replacing the
Center Column.
Remove the Center Column Base Stopper truning
to the way of arrow.
Caution
Inverting the Center Column(Continued)
The Pan Head fixing screw is reversible for either large thread (U3/8) or
small thread (U1/4).
1. Move the Plate Cover down.
2. Loosen the small screw in about three turnings with an Allen wrench
(2mm width).
3. Loosen the Plate without removing the small screw.
U3/8
U1/4
Plate Cover
Small
Screw
Plate
8mm
U3/8
U1/4
4. Loosen the Pan Head fixing screw and pull it out. Then, screw it in
again after reversing top and bottom.
5. Adjust the height of screw in approx. 8mm above the Plate and then,
tighten the small screw by an Allen wrench.
6. Put the Plate Cover back.
Be sure to open all three legs completely in order to prevent camera
shaker, or accidental tip overs caused by unstableness.
SLIK CORPORATION
853 Kayama, Hidaka City, Saitama 350-1231, Japan Phone 81-42-989-2141, Fax. 81-42-985-0210 ©2007
