R
e
d
:
1
2
/24V
B
a
tt.
+
(5A
fu
se
!)
B
lac
k:
1
2
/2
4V
B
a
tt.
-
5A
Receiver Part# 8932
Fu
s
e
d
p
ow
er
s
u
ppl
y
fr
om
a
ci
rc
ui
t
w
ith
O
N
/O
F
F
s
w
itc
h
!
To
bo
w
thr
ust
e
r
Y
e
llo
w
:
S
id
ep
ower
au
to
m
a
tic
m
a
in
swi
tch
(o
pt
ional
)
To
bo
w
thr
ust
e
r
c
o
n
tr
ol
p
a
ne
l
BOW
S
lei
pn
e
r
M
o
tor
A
S
•
No
rw
ay
www
.s
id
e-
powe
r.
co
m
2
b
lue/
b
la
c
k
4r
e
d
(B
+
)
3g
re
y
/b
la
c
k
s
ignal
to
w
ind
-
la
s
s
u
p
s
ignal
to
w
ind
-
la
s
s
d
o
w
n
w
in
d
la
ss
c
o
nt
ro
l
po
w
e
r
(B
+
)
wi
n
d
la
s
s
WLA
S
PROG
LED
R
e
d: 12
/24V
Batt.
+ (5A
fuse!)
B
lack: 1
2
/24
V
Batt
. -
5 A
Fu
sed p
o
wer
supp
ly from
a
ci
rcuit w
ith ON
/OFF s
w
itch!
To
bow
thrust
er
Y
e
llow:
Sidep
o
wer
autom
a
tic
m
a
in sw
itch (o
ption
a
l)
To
bow
thrust
er con
trol p
anel
BOW
S
lei
pn
er
Mot
o
r A
S
• www
.si
de
-p
owe
r.c
o
m
bl
u
e
/b
la
c
k
gr
e
y
/b
la
c
k
re
d (B+
)
signa
l wind
lass u
p
w
indla
ss ctrl.
powe
r
s
ignal
w.lass
down
wi
ndlas
s
WLASS
Receiver Part# 8932A
Y
e
llow:
Not in
use
The original transmitter and receiver have the same factory preset code so that no programming
is necessary. When additional transmitters are to be used, the receiver must be programmed
again for all transmitters.
1. Deactivate the receiver and all transmitters (press “OFF” on all transmitters).
Turn off the main power switch for the thruster(s).
2. Turn on the power to the receiver.
3. Remove the plastic plug from the receiver box (as shown above).
4. Press the “PROG” button at the receiver. The receiver is then in “Program mode”.
The receiver will stay in Program mode for 30 seconds,indicated by blinking LED
5. The receiver and transmitter are programmed by pressing both “ON” buttons on the transmitter
for about 2 seconds. During this 2 seconds the LED will change from blinking to continous light
when the programming signal is received. Turn off transmitter.
6. Additional transmitters must be programmed according to step 5 within the same 30 seconds
time period when the receiver is in “Program mode”.
7. Wait until the LED stops to blink. The total “Program mode” time is about 30 seconds.
The programming is now fi nished.
8. Turn on the transmitter(s) and check that the receiver LED is blinking slowly (User mode)
9. Turn off the power to the receiver and put the plastic plug back in place.
Installation & User Manual, Radio Remote 8985/8986
Page 7
Programming additional receivers