background image

 

 19 / 25

 

Copyright (c) 2016-2017 Shanghai Slamtec Co., Ltd.

 

 

Figure 4-6 Manual Charging Connection 

 

Battery Attention 

Charging 

Do not charge Apollo or its battery with non-official charging devices. 

The battery should be charged within the range pf temperature specified in the 
products Specification. Stop charging immediately when the surface temperature 
of the battery is over 50℃. 

Before charging, please ensure the polarities of the battery are connected properly. 
Reverse charging is strictly prohibited. Reverse charging cannot charge the battery. 
Inversely,  it  will  induce  fatal  damage  to  the  battery  and  even  lead  to  battery 
heating, swelling, leaking, fire and explosion.  

Storage 

The battery should be stored in a cool and dry place. If you are intend to keep the 
battery for a long time (3 months or longer), it is recommended that the battery 
should be  stored  under  the  dry  environment  with  temperature  during  10-25℃ 
and without corrosive gas. And the battery should be charged at least one time 
every six months to ensure the voltage of the battery is between 3.6V-3.9V.  

Attentional Notes 

Since the battery is softly packaged with aluminum foil, it is vulnerable to sharp 
objects. Please do not place the battery with sharp objects.  

Charging port 

Apollo 
emergency 
charging port

 

Summary of Contents for A2M21


























Reviews: