background image

Operating instructions

Access to “SUPERVISOR MODE” for panel

operation

To operate this fire alarm control panel, it is necessary to gain access to

the “Supervisor Mode”, to do this enter the four digit security password

code, on the push buttons. This security code should have been given to

the responsible person on system hand over.
After entering the correct code the “Supervisor Mode” LED will illuminate.

The panel will time out of “Supervisor Mode” if the ‘RESET’ button is

pressed or 20 seconds have elapsed since the last button was pressed.

The following functions can all be employed in the “Supervisor

Mode”.

Sounders ON/OFF

If the panel is in alarm the sounders will sound, the sounder circuits may

be silenced by pressing this button. If the sounders are silent by pressing

this button they will be activated.

Mute panel

To silence the panel’s internal buzzer press “Mute Panel”. The panel will

continue to beep every 8 seconds until reset.

Reset

This will clear any non-latched indications and return the panel to “Code

Entry Mode”. If the cause of the indication is still present the indication will

be re-established within 10 seconds.

Select - Lamp Test

Hold down “Select” for a minimum of 2 seconds. Release

once test

complete.

Test Zone

This feature allows one person to check the detectors and sounders

without having to return to the panel during the testing routine. When the

appropriate zone is in test mode and a detector is activated, the sounder

circuit/s will operate for a few seconds and then automatically reset.

1

Enter the access code to get into “supervisor mode” if not already

entered.

2

Hold down the ‘ADVANCE’ push button for at least

2 seconds until you hear a double bleep.

3

The “Test” LED will light and the Zone 1 Fault LED will flash at a fast

rate (faster than the fault warning flash rate) the flashing LED at this

stage indicates that the zone is not in test!

4

If you do not wish to test this zone then press ‘ADVANCE’ to move

on to the next zone.

5

To put the zone into “Test” press ‘SELECT / LAMPTEST’ (repeated

pressing of this button will toggle the zone in and out of test mode!).

6

After you have pressed the select button you will see that the zone is

now constantly lit, this indicates that the zone is now in test!

7

Once the site tests have been completed you may find that the

keypad access timer has elapsed and that you will have to repeat

points 1-4 to get to the appropriate zone in test.

8

To cancel the test mode and return a zone back to normal operation

simply press ‘SELECT / LAMP TEST’ to toggle the zone from

constant to flashing.

Once you have returned the zone/zones to normal operation you can then

press reset to exit supervisor mode.
Note: Pressing reset whilst a zone is in test will not revert the panel to

normal operation!

4

61600970 issue 9_8/02

4 & 8  zone - Fire alarm panels

1

2

3

4

5

Sounders

ON/OFF

Mute Panel

Reset

Advance

Select

1

2

3

4

ZONE FAULT / TEST / DISABLE

ZONE FIRE

FIRE

Power

General Fault
Sounder Fault/

Disable
System Fault

Power Fault

Disabled

Test
Supervisor

mode

LED Continuous

DISABLE/TEST

LED flashing

FAULT

Code entry

mode

Green indicator

Red indicators

Amber indicators

Amber indicators

Control buttons

Figure 7 Controls and indicators

Summary of Contents for SECURI4









Reviews: