Skyworks Si5391 Reference Manual Download Page 40 | Manualshive

Page: 40 / 94

background image

9. Zero Delay Mode (All Si5391 Devices Except Si5391P)

A zero delay mode is available, in all Si5391 devices except for Si5391P, for applications that require fixed and consistent minimum
delay between the selected input and outputs. The zero delay mode is configured by opening the internal feedback loop through
software configuration and closing the loop externally as shown in

Figure 9.1 Si5391 Zero Delay Mode Setup on page 40

. This helps

to cancel out the internal delay introduced by the dividers, the crosspoint, the input, and the output drivers. Any one of the outputs
can be fed back to the FB_IN pins, although using the output driver that achieves the shortest trace length will help to minimize the
input-to-output delay. The OUT11 and FB_IN pins are recommended for the external feedback connection in the Si5391. The FB_IN
input pins must be terminated and ac-coupled when zero delay mode is used. A differential external feedback path connection is
necessary for best performance. For this reason, customers should avoid using CMOS outputs for driving the external feedback path.
Zero Delay Mode performance will degrade with low values of phase detector frequency (Fpfd). For this reason, ClockBuilder Pro will
not enable Zero Delay Mode with an Fpfd of less than 128 kHz.

When the DSPLL is set for Zero-Delay Mode (ZDM), a hard reset request from either the RSTb pin or RST_REG register bit will have a
delay of ~750 ms before executing. Any subsequent register writes to the device should be made after this time expires or they will be
overwritten with the NVM values. Please contact Skyworks technical support for information on reducing this ZDM hard reset time.

Zero Delay

Mode

IN_SEL[1:0]

IN0
IN0b

IN1
IN1b

IN2
IN2b

÷ P

0

÷ P

1

÷ P

2

VDDO0

OUT1b

VDDO1

OUT1

OUT2b

VDDO2

OUT2

OUT9b

VDDO8

OUT8

OUT 9b

VDDO 9

OUT 9

OUT 9Ab

OUT9A

MultiSynth

&

Dividers

IN3/FB_IN

IN3b/FB_INb

1

0

0

External Feedback Path

PD

LPF

÷

M

n

M

d

÷

N

9n

N

9d

÷R

11

f

FB

=

f

IN

f

IN

÷P

fb

PLL

OUT 0Ab

OUT 0A

OUT0b

OUT0

Figure 9.1. Si5391 Zero Delay Mode Setup

The following table gives the register used for the Zero Delay mode.

Table 9.1. Zero Delay Mode Register:

Reg Address

Bit Field

Type

Setting Name

Description

0x091C

2:0

R/W

ZDM_EN

3 = Zero delay mode.

4 = Normal mode.

All other values must not be written.

Si5391 Reference Manual • Zero Delay Mode (All Si5391 Devices Except Si5391P)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

40

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

40

«
...
38
39
40
41
42
...
»

Summary of Contents for Si5391































































































Reviews:

No comments

Related manuals for Si5391

Brand: Eberg Pages: 14

UEYPOPL/12-4Q/3D

Brand: Cristec Pages: 54

Brand: NextBase Pages: 52

Brand: QFX Pages: 4

Brand: Memorex Pages: 2

Brand: mikroElektronika Pages: 3

Brand: Briggs & Stratton Pages: 156

Brand: Curtis Dyna-Fog Pages: 53

Brand: A-iPower Pages: 112

IntelliHeat ST 115

Brand: Pace Pages: 20

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 47

Brand: Kenwood Pages: 60

Brand: Kenwood Pages: 10

Brand: Kenwood Pages: 33

Brand: Kenwood Pages: 73

Brand: Kenwood Pages: 70

Brand: Kenwood Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands