Skyworks Si5391 Reference Manual Download Page 32

Page: 32 / 94

Table 8.6. Output Impedance and Drive Strength Selections

VDDO

OUTx_CMOS_DRV

Value Setting

Source Impedance (Z

)

3.3 V

0x01

38 Ω

0x02

30 Ω

0x03

22 Ω

2.5 V

0x01

43 Ω

0x02

35 Ω

0x03

24 Ω

1.8 V

0x02

46 Ω

0x03

31 Ω

Note:

1. This setting is strongly recommended.

Table 8.7. LVCMOS Drive Strength Control Registers

Setting Name

Hex Address [Bit

Field]

Function

Si5391 only

OUT0A_CMOS_DRV

0104[7:6]

LVCMOS output impedance. See previous table.

OUT0_CMOS_DRV

0109[7:6]

OUT1_CMOS_DRV

010E[7:6]

OUT2_CMOS_DRV

0113[7:6]

OUT3_CMOS_DRV

0118[7:6]

OUT4_CMOS_DRV

011D[7:6]

OUT5_CMOS_DRV

0122[7:6]

OUT6_CMOS_DRV

0127[7:6]

OUT7_CMOS_DRV

012C[7:6]

OUT8_CMOS_DRV

0131[7:6]

OUT9_CMOS_DRV

0136[7:6]

OUT9A_CMOS_DRV

013B[7:6]

8.4.6 LVCMOS Output Signal Swing

The signal swing (V

) of the LVCMOS output drivers is set by the voltage on the VDDO pins. Each output driver has its own

VDDO pin allowing a unique output voltage swing for each of the LVCMOS drivers.

Si5391 Reference Manual • Outputs

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

Summary of Contents for Si5391































































































Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands

Skyworks Si5391, Reference Manual

Search results

Summary of Contents for Si5391

Reviews:

Related manuals for Si5391

Brands by name

Popular brands