Skyworks Si5391 Reference Manual Download Page 26 | Manualshive

Page: 26 / 94

background image

Table 8.1. Output Driver Crosspoint Configuration Registers

Setting Name

Hex Address
[Bit Field]

Function

Si5391/Si5391P

OUT0A_MUX_SEL

0106[2:0]

Connects the output drivers to one of the N dividers. Selections are N0, N1,
N2, N3, and N4 for each output divider.

OUT0_MUX_SEL

010B[2:0]

OUT1_MUX_SEL

0110[2:0]

OUT2_MUX_SEL

0115[2:0]

OUT3_MUX_SEL

011A[2:0]

OUT4_MUX_SEL

011F[2:0]

OUT5_MUX_SEL

0124[2:0]

OUT6_MUX_SEL

0129[2:0]

OUT7_MUX_SEL

012E[2:0]

OUT8_MUX_SEL

0133[2:0]

OUT9_MUX_SEL

0138[2:0]

OUT9A_MUX_SEL

013D[2:0]

8.2 Output Divider (R) Synchronization

All  the  output  R  dividers  are  reset  to  the  default  NVM  register  state  after  a  power-up  or  a  hard  reset.  This  ensures  consistent  and
repeatable  phase  alignment  across  all  output  drivers  coming  from  the  same  N  divider.  Resetting  the  device  using  the  RSTb  pin  or
asserting  the  hard  reset  bit  will  have  the  same  result.  The  SYNCb  pin  provides  another  method  of  realigning  the  R  dividers  without
resetting the device. This pin is positive edge triggered. Asserting the sync register bit provides the same function. Note that using the
SYNCb bit/pin guarantees that the outputs will align to within the datasheet specifications for outputs that come from the same N divider
only.

Si5391 Reference Manual • Outputs

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

26

Rev. 0.5 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 11, 2022

26

«
...
24
25
26
27
28
...
»

Summary of Contents for Si5391































































































Reviews:

No comments

Related manuals for Si5391

Architectual AQ215

Brand: Martin Audio Pages: 1

Brand: Porter-Cable Pages: 22

Brand: Westfalia Pages: 34

Brand: Wacker Neuson Pages: 52

12.0 BTDAR 50 HERTZ

Brand: Westerbeke Pages: 82

Brand: Stanford Research Systems Pages: 55

Brand: Powermate Pages: 72

Brand: Firman Pages: 114

Brand: Scheppach Pages: 88

Brand: Westinghouse Pages: 106

Brand: THORLABS Pages: 18

Brand: Coby Pages: 9

Brand: Ericsson Pages: 24

Brand: LENCO Pages: 24

Brand: VICI DBS Pages: 41

Brand: ROBLON Pages: 8

Brand: ROBLON Pages: 8

Brand: AADCO Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands