Skyworks Si5332 Manual Download

Page: 24 / 74

Table 5.4. External Crystal Input Specification (A/B/C/D Grades)

= V

DDA

= V

DD_DIG

= V

DD_XTAL

= 1.8 V to 3.3 V +10%/-5%, V

DDO

= 1.8 V ±5%, 2.5 V ±5%, or 3.3 V ±5%, T

= –40 to 85 °C)

Parameter

Symbol

Test Condition

Min

Typ

Max

Units

Crystal Frequency

xtal

16-50

MHz

Load Capacitance

16 - 30 MHz

31 - 50 MHz

Shunt Capacitance

16 - 30 MHz

—

31 - 50 MHz

—

ESR

16 - 30 MHz

—

Ω

31 - 50 MHz

—

Ω

Crystal Drive Level

—

250

µW

Input Capacitance

Internal cap disabled

—

2.5

—

Internal cap enabled

(per pad)

—

Input Voltage

XIN

-0.3

—

1.3

Notes:

1. Internal capacitance on the xtal input pads is programmable or can be disabled. Please reference section 5.3.1 for more detailed

information.

Table 5.5. Embedded Crystal Specifications

Parameter

Symbol

Test Condition

Min

Typ

Max

Units

Initial Accuracy (E/F/G/H/L Grades)

Measured at +25 °C at

time of shipping

—

±10

—

ppm

Total Stability (E/F/G/H/L Grades)

–40 °C to +85 °C

–50

—

ppm

Total Stability (L-Grade Only)

+25 °C to +85 °C

–30

—

ppm

Temperature Stability (E/F/G/H/L Grades)

–40 °C to +85 °C

–30

—

ppm

Temperature Stability (L-Grade Only)

+25 °C to +85 °C

–25

—

ppm

Note:

1. Internal crystal loading capacitance is set at factory during device frequency calibration and can not be changed.

Si5332 Data Sheet • Electrical Specifications

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 1.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 16, 2021

Summary of Contents for Si5332











































































Search results

Summary of Contents for Si5332

Reviews:

Related manuals for Si5332

Brands by name

Popular brands

Skyworks Si5332, Manual

Search results

Summary of Contents for Si5332

Reviews:

Related manuals for Si5332

Brands by name

Popular brands