background image

01/11/2017

5/36

E_MH_Mounting_instructions_Skylux_Climalux

General installation tips

Please read this manual carefully.

The installation must be carried out by people with sufficient technical knowledge and experience in the area of 

conservatory installations. The installer must take the required safety measures into account during the installation 

such as the use of scaffolding and personal protection equipment - safety shoes, helmet (i.e. hard hat), gloves, 

safety goggles, etc. - to ensure the work is carried out in a safe environment. During installation, please make sure 

that the necessary precautions have been taken to ensure the stability of the unfinished construction.

Fixing material

The selection of required fixing material is to be made in function of the foundation or the walls. Check whether 

the foundation and the walls on which the structure is to be anchored have a sufficient load-bearing capacity. The 

installer is responsible for the assessment of the appropriate fixing materials for the load and foundation on which 

the structure is to be fixed. Please contact your fixing material supplier or specialised engineering consultants in 

case of doubts. Skylux cannot be held responsible for the installation or the fixing materials used.

Seal installation

A distinction is made between push-in seals and slide seals. 

The seal of a push-in seal is pushed into the profiles. The C2CX, C8 and CY10 seals are push-in seals. 

The slide seals C1CX & C3 are slid into the profiles. 

The seals C1CX and C2CX are equipped with an anti-stretch wire that prevents the seal from being stretched 

during installation. This technology ensures that the seal cannot shrink after installation. 

Avoid the use of silicone and detergent when installing the seals. Plastic sheets can be damaged by these products. 

Plastic sheets can result in settlement noise due to temperature fluctuations. This will not affect the guarantee and 

will not be accepted as a claim.

Terms, conditions and guarantee

The guarantee is void when the installation instructions provided below are not followed. Not following the 

instructions and/or using other parts may have an adverse effect on the safety and life cycle of the product. 

Variations are not permitted without written permission of the manufacturer. Our installation instructions manual 

and film are based on the latest level of our knowledge and technics. We cannot be held responsible for possible 

incomplete information. Always check if our product is suited for your application. As the manipulation and the 

mounting of the product are done beyond our control, can Skylux not be held responsible for possible damages. 

The installer must take the specified span values in relation to the glazing and load (snow and wind) according 

to the applicable standards into account. The load graphs that you will find in this manual on page 31-33 are 

only indicative. Contact the manufacturer, architect or engineering consultant for conservatory roofs outside 

the normal range. The manufacturer reserves the right to change this manual without prior verbal or written 

notification.

Skylux reserves the right to change this manual without prior notification. Changing the installation requirements 

or the product will not mean a right to any compensation or exchange of parts. 

The latest version of this manual can be consulted by visiting www.skylux.be.

Climafast

The Climafast calculation application is offered by Skylux for free and is at disposal of the professionals. You 

will receive information on how to log on and download the Excel version of the application upon request. With 

Climafast, you can determine the price of your Climalux roof. An overview of profiles, lengths, parts, allowed 

loads, etc, is provided for each project. The aim of this application is to inform the user. 

Skylux reserves the right to change the Climafast application without prior notification. The results of the 

application are indicative and do not give right to any compensation. The latest version of the calculation 
application can always be downloaded from www.skylux.be.

Summary of Contents for Climalux 36179





































Reviews: