8.
OTHER
HOUSEHOLD
ALERT ® SENSORS
The Household Alert
®
Long Range Receiver can work with up to 4
di
sensors: garage door monitor sensor, door / window sensor,
water sensor, indoor/outdoor motion sensor, etc. Please visit
www.skylinkhome.com or contact us at [email protected] for
more information of how to fully utilize your Wireless Motion Alert.
6. OPERATION (CONT)
When the battery level on the sensor drops to a certain level, or the
sensor is out of the operating range, the receiver will show a “loss of
signal” indication. The red LED representing that zone will
rapidly,
i.e. if zone 1 sensor is lost, the zone 1 red LED will
rapidly.
When the loss of signal indication occurs, move the receiver closer to the
corresponding sensor and trigger that sensor. If the red LED stops
ing rapidly, that means the receiver or sensor needs to be relocated. If the
“loss of signal” indication persists, replace the battery of that sensor.
7. LOSS OF SIGNAL INDICATION
10. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING:
Changes or
to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equi pment dose cause harmful interference to radio or television
reception, which can be determined by turning the equipment and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit
from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
9. FCC
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z756
©2010 SKYLINK GROUP
If you would like to order Skylink’s products or have
getting them to
work or download information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
11. CUSTOMER SERVICE
Mute
When a sensor is triggered for a long period of time, you may stop the
buzzer by pressing the mute button. When another signal comes again,
you can disable the buzzer for all currently activated sensors by pressing
the mute button. The receive will beep again if it receives another signal.
For instance, if you are working in your
garage, you may want to disable the
buzzer for this garage only. Then you can
press the “Mute” button after it starts to
sound. If any other sensor is triggered,
the receiver will sound again.
Alarm
When the receiver is in Alarm operation mode, it will sound its siren
when a sensor is activated. The maximum alarm duration is set for 3
minutes. To terminate the siren during the 3-min interval, press the mute
button. Although the alarm siren is terminated, if that sensor is still
activated, its corresponding LED will continue to
Note: This audio siren is not intended to prevent intruder break-in, it is
rather an alert signal indicating a sensor is activated. Therefore,
turning
the siren does not require
password.
O
No audio will be emitted even sensor is activated. Only zone LED will
.
Page 3 of 3
