Skutt EnviroVent 2 Operating Manual Download Page 7

7

S

ETUP

S

TEP

 5 - I

NSTALLING

 

THE

 

PLENUM

 

CUP

 

AND

 

SPRING

 

STAND

Using gloves to protect your hands, stretch the fl ex tubing to the proper length for 

your installation.   Stretch out the last 3” of tubing on each end of the duct to ensure 

they are wide enought to fi t over their connections.  Be careful not to collapse the 

open end of the fl ex tubing.  You should be able to stretch the fl ex tubing 6 ft. to 8 ft. 
Attach the length of 3” diameter aluminum fl ex tubing to the 3” sleeve on the ple-

num cup and secure with the hose clamp.   
 Place the spring over the plenum cup stand post and insert the 7/16” stand post 

into the small hole in the bottom of the  aluminum plenum cup.  Refer to the instal-

lation drawing if necessary.  When properly assembled the plenum stand should be 

spring loaded into the bottom of the plenum cup.
Place the plenum cup and stand under the holes drilled in the kiln fl oor by rotat-

ing the cup horizontally, compressing the spring to permit cup rotation to vertical 

and releasing the spring tension.  Ensure that the plenum cup is centered under the 

holes in the kiln’s fl oor.

S

TEP

 6 - I

NSTALLING

 

THE

 

BLOWER

 

AND

 

MOTOR

 

ASSEMBLY

Locate a spot on the wall to mount the blower assembly and discharge tube.  Im-

portant:  Choose a spot that is close enough for the aluminum fl ex tubing to reach.   

Remember that the kiln must be a minimum of 18” from the wall.   If possible, locate 

a spot that allows you to mount the vertical edge of the mounting plate into a wall 

stud or ceiling joist.  If you need to go further then the ducting will allow consult the 

Custom Installation section of this manual. 
Drill a 3 1/8” clearance hole in the wall or ceiling to accept the 3” diameter dis-

charge pipe.  Be sure to check for wires and pipes in the wall prior to drilling.  
Insert the discharge pipe through the 3 1/8” hole and fasten the mounting plate in 

place using the supplied sheet metal screws or toggle bolts.  Choose the proper fas-

tener for your wall type of material.  If you are using the toggle bolts you will need 

to position the mounting plate and mark where the holes will be.  Predrill the holes 

for the toggle bolts using a 3/8” drill bit .  The  3” metal discharge tube is supplied 

at 8” in length.  This tube may be trimmed shorter or added to in order to allow for 

any installation.
Attach the open end of the aluminum fl ex tube to the blower inlet fl ange using the 

hose clamp provided.   Check the plenum cup assembly to make sure it has not 

shifted out of place.
We recommend attaching a hood with a screen over the end of the discharge tube.   

This will help prevent snow, rain or debris from entering into the discharge tube or 

blocking the air fl ow.  The screen is important to prevent small animals and insects 

from entering the tube.  This item is not included with the kit but can usually be 

found at local hardware stores.

F

LOOR

 M

OUNTED

 V

ENTS

A bolt-on plate comes with your kit and allows you to place the vent motor on the fl oor when wall-mounting is 

not possible.  To install, just bolt the fl oor plate on to the bottom lip of the mounting plate using the hardware in-

cluded in the kit.   This allows the motor to sit upright on the fl oor.   Install ducting to the discharge tube and vent 

it as you would a dryer.  When the vent is fl oor mounted it is no longer a negative pressure system.

Summary of Contents for EnviroVent 2

















Reviews: