SKLZ.com
PRO MINI HOOP SYSTEM
STEP 4
– RIM AND BACKBOARD ASSEMBLY
Align the holes on the Rim Plate with the Backboard (11) fitting the Rim Plate into the
back of the backboard. Using the 1.5” bolts, attach the Rim (12) to the Backboard (11).
Assemble so that the washers are next to the nuts. Tighten each nut with one of the
provided 2-Sided Wrenches to secure the Rim to the Backboard. Attach the net to the
rim by looping the long end of the net over the metal loops.
STEP 5
– BRACKETS AND BACKBOARD ASSEMBLY
Using the 1.5” hex bolts, attach the Lower Backboard Brackets
(9) to the bottom of the Backboard (11) and tighten with the
2-Sided Wrenches provided.
NOTE: Attach the short sides of Backboard Brackets to the
Backboard. Make sure when brackets have been attached
they come in towards each other.
Attach the Upper Backboard Brackets (10) with the remaining
1.5” hex bolt to the top of the Backboard and tighten with the
2-Sided Wrenches provided.
STEP 6
– BACKBOARD AND TOP POLE ASSEMBLY
Using a 3.25” hex bolt, attach the Upper Backboard
Brackets (10) to the top of the Top Pole (4). Tighten
to secure. Do not over tighten as these joins will
move to raise or lower the backboard. Then attach
the Lower Backboard Brackets (9) to the pole by
aligning the holes in the middle of the bracket.
Loosely tighten the nut with your fingers. (Will fully
tighten in STEP 7).
NOTE: Make sure that the pole connector is facing
away from the backboard.
ASSEMBLY
STEP 1
– BOTTOM POLE AND BASE ASSEMBLY
Attach the Bottom Pole (2) to the Base (1) by sliding the pole
into the square hole at the front of the Base. Make sure that the
Bottom Pole connector is facing the back of the Base. Push the
Bottom Pole all the way into the Base.
Turn the Base on its side and slide the one locking washer onto
the 1” bolt followed by the 1” washer. Screw the bolt
into the Base and Bottom Pole using a 2-Sided Wrench.
Turn the Base back over and fill halfway with water or
with 50 pounds of sand to stabilize the system while the
unit is built. Snap the Red Base Cap into the Base.
STEP 2
– BASE ARMS AND BOTTOM POLE ASSEMBLY
Connect Base Arms (5 & 6) to Bottom Pole (2) using the 2.5” hex bolt.
Loosely tighten the nut with your fingers, do not tighten all the way.
(Will fully tighten at the end of STEP 3).
NOTE: When using a bolt, nut and two washers
make sure that the washers are always
used on each end of the bolt.
STEP 3
– BASE ARMS AND BASE ASSEMBLY
Place one Bottom Base Plate under and one Top
Base Plate over the holes on one side of the base.
Note: To align the Bottom Base Plate, place the
rounded corner into the inner top corner
of the Base.
Align the holes and slide one 1.25” hex bolt up
through the Bottom Base Plate. This bolt will
connect in order from bottom to top; Bottom
Base Plate, Base, Top Base Plate, Base Arm (see
illustration). Add the washer and loosely finger
tighten the nut. Slide a second 1.25” hex bolt up
through second hole on the Bottom Base Plate.
Secure both nuts with the 2-Sided Wrenches provided.
Repeat on the other side.
Now tighten the nut that connects the Base Arms to the Bottom
Pole with the 2-Sided Wrenches provided. Set aside.
Connector is facing
the back of the base
Rim Plate
Backboard
Rim
Rim and Backboard Assembly
Net attachment
Washers
View of Back of Backboard
Connector is facing
away from the backboard
Base
Top Base Plate
Base Arm
Hardware not to scale
Bottom
Base Plate