background image

-9-

may shatter if the front on the blade hits the
work and/or the footplate. 

5. When cutting metal:

- Apply a lubricant for easier, smoother,

faster cutting and longer blade life. 

- For non-ferrous metals, aluminum,

bronze or brass, use a stick wax on the
blade. 

- For ferrous metals, iron and steel, use

machine or cutting oil along the surface
to be cut.

6. When cutting thin metal, "sandwich" the

material between two pieces of scrap wood.
Clamp or put in a bench vise. One piece of
lumber on top of the metal can be used with
adequate clamping. Place your cut lines or
design on the wood. 

7. Don’t force the cutting. Let the saw and

blade do the work.

WRONG                           RIGHT

POCKET/PLUNGE CUTS

The reciprocating saw can be used to make
plunge cuts into softer material, (for example,
wood or light building materials for walls),
without a starting hole (Fig. 7).

1. Mark the line to be cut clearly on the work.

2. Set the tool with one edge of the footplate
firmly against the material.

3. Place the tip of the blade (not running) on the
line to be cut.

4. Tilt the saw so that the blade clears the work.

5. Squeeze the trigger switch and carefully
engage the moving saw blade into the material.

6. After the blade penetrates through the work,  

continue sawing along the marked outline.

NOTES:

To make plunge cutting easier, use a heavy
gauge blade, install the blade with the teeth
facing upward, and hold the saw upside down
as shown (Fig. 8).

Do not plunge cut in metal surfaces. 

In thick materials and in harder materials,
such as metal, plunge cutting should not be
attempted. Such materials can be cut with the
recip saw only by starting the cut from the
edge of the material or from a hole drilled all
the way through the material that is large
enough to fit the saw blade.

The use of any accessories
not specified in this manual

may create a hazard.

!

WARNING

FIG. 7

FIG. 8

SM 2610001755 07-08  7/14/08  9:41 AM  Page 9

Summary of Contents for 9215

































Reviews: