Skil 3850 Series, Original Instructions Manual

Page: 12 / 124

12
! select operating mode only when tool is switched
off and plug is disconnected
-
the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
-
it takes a short time for the hammer mechanism to
reach full impact power
-
best hammer drilling results can be obtained by only a
slight pressure on the tool; drilling performance will not
improve by applying more pressure on the tool
• Chiseling with rotating chisel
e
! switch off the tool and disconnect the plug
- select “rotating” chiseling mode
• Chiseling with fixed chisel
r
! switch off the tool and disconnect the plug
- select “rotating” chiseling mode
- place chisel in desired position
-
select “fixed” chiseling mode
• Battery protection
Switches off the tool or prevents the tool from being
switched on, when
- the load is too high
-
the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
- the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• Adjusting drilling depth
u
• Holding and guiding the tool
t
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle H (can be adjusted as
illustrated)
y
- keep ventilation slots E
2
uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
• Use the appropriate bits
i
! only use sharp bits
• For drilling with non SDS drill bits in wood, metal and
plastic, use an adapter (not standard included)
o
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C
2
and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
-
pull adapter to check whether is it locked correctly
- set switch D
2
to normal drilling (only activate when
tool is switched off and the switch is locked)
• When drilling ferrous metals
-
pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• Splinterfree drilling in wood
p
• Dustfree drilling in walls
a
• Dustfree drilling in ceilings
s
• Drilling in tiles without skidding
d
• For more information see www.skil.com
BATTERIES
• The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
• Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
-
SKIL charger: CR1*31****
• Do not use the battery when damaged; it should be
replaced
• Do not disassemble the battery
• Do not expose tool/battery to rain
• Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
-
during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3
Read the instruction manual before use
4
Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5
Store tool/charger/battery in locations where temperature
will not exceed 50°C
6
Do not dispose of electric tools and batteries together
with household waste material
USE
• Combined switch for on/off and speed control A
2 8 9
- control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery
2
• Battery level indicator
7
- press the battery level indicator button F to show the
current battery level.
• Changing direction of rotation
q
-
when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits
w
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
- pull accessory to check that it is locked correctly
-
remove accessory by pulling back locking sleeve C
! the SDS+ accessory requires freedom of
movement which causes eccentricity when tool
is off-load; however, the accessory automatically
centres itself during operation without affecting
drilling precision
! do not use bits with a damaged shank
• Selecting operating mode
e
-
turn switch D to the desired operating mode until it
snap-locks
1 = normal drilling/screwdriving
2 = impact drilling
3 = chiseling with rotating chisel
4 = chiseling with fixed chisel