18
•
If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
•
Assembly
-
assemble the transport handle E with 2 bolts using hex
key AN
9
-
assemble the mitre lock knob AE into the front of the
table
q
-
assemble the sliding fence U (see Adjusting sliding
fence(s))
•
Transport/working position
For releasing the tool (
working
position)
-
press handle B
8
downward with one hand while
pulling out locking pin C with the other hand
w
a
-
guide the head assembly slowly upward
For securing the tool (
transport
position)
-
slide the head assembly to the stop in the direction
of fence S (keep approx. 5 cm distance) and tighten
locking knob AH
w
b
-
set the bevel angle to 0° (see Setting bevel angle)
-
set the mitre angle to 45° left or right (see Setting mitre
angle)
-
press handle B downward with one hand while pushing
locking pin C with the other hand
-
wind up the power cord
-
use transport handle E
8
for carrying the tool
w
d
-
alternatively, use the side handles for carrying the tool
w
e
! never lift the tool by holding the main handle, or
the power cord
•
Mounting tool on working surface
e
!
for safe handling always mount tool on a flat and
stable working surface (e.g. workbench)
-
use 4 mounting holes F for attaching the tool with
suitable screws to the working surface
-
you may also clamp the tool to the working surface with
commercially available screw clamps
-
for stabilizing the tool the height of support foot G can
be adjusted
-
alternatively, the tool can be mounted onto a mitre saw
stand
! read all the warnings and instructions included
with the saw stand
•
Dust/chip extraction
r
-
mount dustbag H/vacuum cleaner as illustrated
-
empty dust bag regularly for optimal dust pick-up
performance
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
•
Saw table extension
t
-
use knobs L to fasten extension bars K (on either side
of the tool)
-
the length of extension bars K is steplessly adjustable
from minimum to maximum
•
Clamping the workpiece
y
!
for optimum working safety always firmly clamp
the workpiece with the adjustable clamp supplied
-
do not work with workpieces that are too small to clamp
-
for
maximal
workpiece dimensions use table
u
as
reference
-
fasten workpiece clamp into support hole N with knob P
(on either side of the tool)
•
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
•
Never use saw blades made of high speed steel (HSS)
•
Do not use a saw blade which is cracked, deformed or
dull
•
Only use saw blades with a hole diameter which fits the
tool spindle without play; never use reducors or adaptors
to fit large-hole saw blades
•
Protect accessories from impact, shock and grease
DURING USE
• Do not force the tool
(apply light and continuous
pressure in order to avoid overheating the blade tips and,
in case of cutting plastics, melting the plastic material)
•
Keep fingers, hands and arms away from the rotating
saw blade
•
If the saw blade becomes blocked, switch off the tool
immediately and disconnect the plug; only then remove
the wedged workpiece
•
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
•
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
the service organization.
LASER RADIATION
• Do not direct the laser beam at persons or animals
and do not stare into the direct or reflected laser
beam yourself, not even from a distance
(you could
blind somebody, cause accidents or damage your eyes)
•
If laser radiation strikes your eye, you must deliberately
close your eyes and immediately turn your head away
from the beam
•
Do not make any modifications to the laser equipment
•
Do not look into the laser beam (laser radiation)
•
Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam
•
Do not operate the tool in the presence of flammable
liquids, gases or dust
•
Do not operate the tool with children around
•
Do not replace the installed laser with another laser type
AFTER USE
•
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
•
Only remove cut-offs or other parts of the workpiece from
the cutting area when all moving parts have come to a
complete standstill
•
The saw blade becomes very hot during use; do not
touch it before it has cooled down
•
Store the tool
indoors
in a dry and locked-up place, out
of reach of children
EXPLANATION OF SYMBOLS ON TOOL
2
Read the instruction manual before use
3
Wear protective glasses and hearing protection
4
Danger area! No hands zone. Keep hands, fingers or
arms away from this area.
5
Double insulation (no earth wire required)
6
Do not dispose of electric tools and batteries together
with household waste material
7
Laser radiation / Do not stare into beam / Class 2
laser product
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
Summary of Contents for 1320
