background image

MMR2003-050_00_02A.FM

XI

INTRODUCTION

LOCTITE 
APPLICATION PROCEDURE

The following describes the most common appli-
cation procedures when working with Loctite
products.

NOTE:

Always use proper strength Loctite prod-

uct as recommended in this

 Shop Manual

.

THREADLOCKER 

Uncovered Holes (bolts and nuts)

1. Apply here
2. Do not apply

1. Clean threads (bolt and nut) with solvent.

2. Apply Loctite Primer N (P/N 293 800 041) on

threads and allow to dry.

3. Choose proper strength Loctite threadlocker.

4. Fit bolt in the hole.

5. Apply a few drops of threadlocker at proposed

tightened nut engagement area.

6. Position nut and tighten as required.

Blind Holes

1. On threads
2. On threads and at the bottom of hole

1. Clean threads (bolt and hole) with solvent.

2. Apply Loctite Primer N (P/N 293 800 041) on

threads (bolt and nut) and allow to dry for 30
seconds.

3. Choose proper strength Loctite threadlocker.

4. Apply several drops along the threaded hole and

at the bottom of the hole.

5. Apply several drops on bolt threads.

6. Tighten as required.

Stud in Blind Holes

1. On threads
2. On threads and in the hole
3. Onto nut threads

A00A3LA

1

2

A00A3MA

1

2

A00A5RA

2

1

3

Summary of Contents for Tundra R Skandic LT 2003





















Reviews:

Related manuals for Tundra R Skandic LT 2003