background image

 

Failure to comply with the instructions 
and safety information could result in 
malfunction of the unit, fire hazard, or 
electrical shock.

W a r n i n g

 

To avoid serious injury or death from 
electrical shock or fire:
• 

Do not

 handle this fixture or try to 

plug it in when your hands are wet or 
damp, when you are standing on a 
wet or damp surface, or in water.

•  This fixture 

must always be used

 in 

accordance with all electrical and 
safety codes and ordinances, including 
the most recent National Electric Code 
(NEC) and with the Occupational 
Safety and Health Act (OSHA) vol. 1 
on general industry standards and 
interpretations.

• 

Always

 make certain that the power 

source conforms to the requirements 
on the fixture.

• 

Always

 disconnect the power before 

servicing or inspecting the fixture for 
any reason.

•  This fixture is only for use with 110 to 

125 V AC rated products, and is 
equipped with an approved 3-con-
ductor cord with a 3-prong, grounded 
plug.

• 

To reduce the risk of electrical 
shock

, it should only be plugged into a 

properly grounded 3-prong outlet.

• 

Fixture is not waterproof

 and is not 

intended for use in showers, saunas, 
or potentially wet locations. 

Always

 

keep this fixture away from sinks, 
tubs, showers, etc. 

Never attempt to 

pick up plugged-in appliances or 
tools when they fall into water. Fatal 
electrocution could result.

•  This fixture comes equipped with  

a 3-prong grounded plug. 

Do not

  

remove the 3rd prong or otherwise 
try to modify the plug. If it will not fit 
the outlet, have the proper outlet  
installed by a qualified electrician.  
Improper connection of the grounding 
conductor can result in a risk of elec-
trical shock.

• 

Never

 attempt to plug the fixture into 

a non-grounded outlet or extension 
cord and 

always

 be sure that the ex-

tension cord is in good electrical con-
dition and is a minimum of 16 gauge, 
3 conductor.

•  This fixture is intended for use as a 

general indoor power source. 

Do not

 

use in potentially dangerous locations, 
such as in flammable or explosive 
atmospheres. 

W a r n i n g

4

Summary of Contents for LINCOLN 91026









Reviews: