manualshive.com logo in svg

SKF LAGD 1000 series, Instructions For Use Manual

Share
Download
SKF LAGD 1000 series Instructions For Use Manual Download Page 20

20

SKF LAGD 1000

4.  Operation of LAGD 1000/AC.. and LAGD 1000/DC.. units

4.1  LAGD 1000/AC.. & LAGD 1000/DC.. display and control unit

A transparent plastic cover, to protect against water splashes and mechanical damage,
protects the display and control unit. To program or to display the current functions,  
the cover has to be removed using a screwdriver. Replace the cover after use to protect 
the unit.

Led display

LAGD 1000/AC..
LAGD 1000/DC..

 

 

• Seven-segment display: Values and operating state

  

   PAUSE 

h/lmp

  

• Pause time

  

   CONTACT 

min/lmp

 

• Pump operation

  

  CS

 

• CMonitoring of system function by means of an external  

 

   cycle switch CS = Cycle Switch

  

  PS

 

• NOT USED FOR LAGD 1000. This LED must not light

  

  FAULT

 

• Fault message

Push buttons

 

 

 

 

• Turn on display

 

• Display values and parameters

 

• Call up the last parameter in the programming mode

 

• Set values and parameters

 

 

• Change between programming and display mode

 

• Conirm values

 

 

• Activate intermediate lubrication

 

• Clear fault message

Summary of Contents for LAGD 1000 series






































Reviews:

No comments

Brands by name

Popular brands

Load more brands