manualshive.com logo in svg

SKF CMIN400, Manual

Share
Download
SKF CMIN400 Manual Download Page 8

 

 

FIVE-YEAR WARRANTY 
 
Products warranted for five (5) years by SKF are as follows: all standard 
seismic sensors (accelerometers and velocity transducers). 
 
OTHER SKF PRODUCTS 
 
Any SKF product supplied hereunder but not covered by this limited 
warranty shall be either covered by the applicable SKF limited warranty 
then in place for such product or, if no such warranty exists, shall be 
covered by the 90-day warranty stated above. 
 
THIRD PARTY PRODUCT WARRANTIES 
 
For any third party products sold to Buyer by SKF, SKF will transfer to 
Buyer any warranties made by the applicable third party product vendor to 
the extent such warranties are transferable. 
 
CONDITIONS 
 
As a condition to SKF’s warranty obligations hereunder and if requested or 
authorized in writing by SKF, Buyer shall forward to SKF any Product 
claimed by Buyer as being defective.  Buyer shall prepay all transportation 
charges to SKF’s factory or authorized service center.  SKF will bear the 
cost of shipping any replacement Products to Buyer.  Buyer agrees to pay 
SKF’s invoice for the then-current price of any replacement Product 
furnished to Buyer by SKF, if the Product that was replaced is later 
determined by SKF to conform to this limited warranty. 
 
SKF shall not be obligated under this limited warranty or otherwise for 
normal wear and tear or for any Product which, following shipment and 
any installation by SKF (if required by the contract with the Buyer), has, in 
SKF’s sole judgment, been subjected to accident, abuse, misapplication, 
improper mounting or remounting, improper lubrication, improper repair 
or alteration, or maintenance, neglect, excessive operating conditions or 

Summary of Contents for CMIN400


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands