manualshive.com logo in svg

SKF CMIN400, Manual

Share
Download
SKF CMIN400 Manual Download Page 22

Introduction 
Scanning Module 

1 - 10 

Inspector 400 Ultrasonic Probe 

User Manual 

plugged in to the front end of the metered pistol 
housing by aligning the plug with the receptacle and 
inserting it firmly.  

 

Figure 3.  The Scanning Module. 

To use the Scanning Module:  

•

 

Plug in to front end.  

•

 

Start with the sensitivity selection dial at 
maximum (8).  

•

 

Start to scan the test area.  

•

 

Measure from the “gross to the fine.”  If there is 
too much ultrasound in the area, reduce the 
sensitivity, place the Rubber Focusing Probe 
(described below) over the scanning module and 
proceed to follow the sound to the loudest point.  
If it is difficult to locate the sound due to a high 
intensity signal, keep reducing the sensitivity 
and follow the meter to the loudest point.  

Rubber Focusing Probe

 - The Rubber Focusing 

Probe is a circular shaped rubber shield used to block 
out stray ultrasound, and to assist in narrowing the 
field of reception of the Scanning Module.  It also 

Summary of Contents for CMIN400


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands