manualshive.com logo in svg

SKC DPS, Operating Instructions Manual

Share
Download
SKC DPS Operating Instructions Manual Download Page 3

Pre5

Table of Contents

Introduction ............................................................................................ 1

Performance Pro

fi

 le .............................................................................. 2

Principle of Operation ........................................................................... 3

Media Preparation ................................................................................. 4

Impactor Preparation ............................................................................ 4

Cleaning ....................................................................................................................... 4

O-ring Care ................................................................................................................... 4

Inserting a Collection Filter into the IMPACT Sampler ................................................. 5

Inserting an Impaction Disc into the IMPACT Sampler ................................................ 6

Sample Pump Operation ....................................................................... 7

Charging the Battery .................................................................................................... 7

Reading the Charging Status LED ............................................................................... 8

Battery Setup ................................................................................................................ 8

Battery Replacement .................................................................................................... 9

Leland Legacy Quick Guide ....................................................................................... 10

Calibration and Sampling ................................................................... 11

Calibration .................................................................................................................. 11

Sampling .................................................................................................................... 12

Sample Removal, Shipping, and Analysis ........................................ 13

Removing the Collection Filter and Impaction Disc .................................................... 13

Shipping Samples ...................................................................................................... 13

Analysis ...................................................................................................................... 13

Ordering Information ........................................................................... 14

Li-Ion Battery Shipment ...................................................................... 16

Warranty ............................................................................................... 16

 

Indicates a reminder or note

  

Indicates a warning or caution

Summary of Contents for DPS




















Reviews:

No comments

Brands by name

Popular brands

Load more brands