SKC AirLite 110-100-T Operating Instructions Manual Download Page 11

Form 37182 Rev 201019

Page 11 of 12

Appendix

Performance Profile

Flow Range

1000 to 3000 ml/min (5 to 500 ml/min requires low flow accessories. 

See Accessories.

)

Flow Control

Patented* system holds constant flow to ± 5% of set-point

Compensation Range 

(for a minimum of 8-hour 

operation)

1000 ml/min at 30 inches water back pressure

2000 ml/min at 20 inches water back pressure 

3000 ml/min at 10 inches water back pressure

Typical back pressure of 

sampling media 

(inches water)

Flow Rate (L/min)

1.0

1.5

2.0

2.5

3.0

Filter/Pore Size (µm)

25-mm MCE/0.8

6

9

12

15

25-mm MCE/0.45

14

22

35

37-mm MCE/0.8

2

3

4

5

6

37-mm PVC/5.0

1

1

2

2

2.5

Compare the information in this table to pump compensation range to determine appropriate applications.

Temperature Ranges

Operating:

 32 to 104 F (0 to 40 C)

Storage:

 -4 to 113 F (-20 to 45 C)

Compensated Temperature 

Range

41 to 122 F (5 to 50 C)

Operating Humidity

0 to 95% non-condensing

Power

Three standard AA alkaline batteries

Rechargeable AA size 1.2-volt NiMH batteries may be used but will provide approximately 

half the run time stated for disposable batteries.

Tubing

Requires 1/4-inch ID tubing

Case/Material

Plastic, RFI/EMI-shielded

Certifications

CE marked

Battery Run Time

Depends on batteries used. 

See Table 1.

Intrinsic Safety

Do not operate AirLite with Timer in hazardous or explosive locations. AirLite is designed for 

applications that do not require intrinsic safety.

Dimensions

4.6 x 3 x 1.75 in (11.7 x 7.6 x 4.4 cm)

Weight 

(including batteries)

12 oz (340 grams)

 

*  U.S. Patent No. 6,741,056

Summary of Contents for AirLite 110-100-T













Reviews: