SKC AirLite 110-100-T Operating Instructions Manual Download Page 1

Form 37182 Rev 201019

Page 1 of 12

AirLite Sample Pump with Timer

Cat. No. 110-100-T

Operating Instructions

Figure 1.

 AirLite Sample Pump with Timer

863 Valley View Road, Eighty Four, PA 15330  USA • Tel: 724-941-9701 • www.skcinc.com

Accessory 

mounting 

screws

Protective 

control cover

 

(raised)

Belt clip

 (back of pump)

Battery compartment

Pump inlet 

(inlet filter 

underneath)

Bottom view

Top view

Battery compartment door

Flow 
adjustment 
screw

On/off 
button

Battery 
compartment 
screw

Hinge

Introduction

Description

The AirLite Sample Pump with Timer 

(Figure 1)

 provides 5 to 3000 ml/min flows and is suitable for abatement, indoor air sampling, 

and emergency response in non-hazardous locations.

Checking Pump/Kit Contents

Use the table below to verify that you received all items associated with the Cat. No. ordered. If you are missing items, contact  
SKC at 800-752-8472 (U.S. only) or 724-941-9701.

If You Ordered Cat. No. Your Package Should Contain
110-100-T

AirLite Sample Pump with Timer only, with three AA alkaline batteries and screwdriver set

110-100-TK5

High Flow Sample Pump Kit includes 5 pumps as described above and filter cassette holders, in a Pelican case

110-100-TK5D

High/Low Flow Sample Pump Kit includes 5 pumps as described above, filter cassette holders, All-in-One adjustable 
tube holders, and Type A protective tube covers, in a Pelican case

Required Equipment

 

1/4-inch ID tubing

 

Low flow accessories

 if sampling at 5 to 500 ml/min.

 See Accessories.

Front view

LCD

Summary of Contents for AirLite 110-100-T













Reviews: