background image

19

GUARANTEE CONDITIONS

For our devices we provide a warrant

y as defined below.

1. 

In accordance with the following conditions (numbers 
2-5) we repair defect or damage to the device free of 
charge, if the cause is a manufacturing defect. There-
fore, these defects / damages need to be reported to us 
without delay after appearance and within the warranty 
period of 24 months after delivery to the end user. The 
warranty does not cover parts, which easily break (e. 
g. glass or plastic). The warranty does not cover slight 
deviations of the product, which are insignificant for 
usability and value of the device and damage caused 
by chemical or electrochemic

al effects and damages 

caused by penetration of water or generally force 
majeure damage.

2.  The warranty achievement is the replacement or repair 

of defective parts, depending on our decision. The 
cost of material and labor will be borne by us. Repairs 
at customer site cannot be demanded. The proof of 
purchase along with the date of purchase and / or 
delivery is required. Replaced parts become our prop-
erty.

3.  The warranty is void if repairs or adjustments are made, 

which are not authorized by us or if our devices are 

equipped with additional parts or accessories that are 
not adapted to our devices. Furthermore, the warranty 
is void if the device is damaged or destroyed by force 
majeure or due to environmental influences and in 
case of improper handling / maintenance (e.g. due to 
non-observance of the instruction manual) or mechan-
ical damages. The customer service may authorize you 
to replace or repair defective parts after telephone 
consultation. In this case, the warranty is not void.

4.  Warranty services do not extend the warranty period 

nor do they initiate a new warranty period.

5.  Further demands, especially claims for damages which 

occured outside the device, are excluded as long as a 
liability is not obligatory legal.

6.  Our warranty terms - which cover the requirements and 

scope of our warranty conditions - do not affect the 
contractual warranty obligations of the seller.

7.  Parts of wear and tear are not included in the warranty.
8.  The warranty is void if not used properly or if used in 

gyms, rehabilitation centers and hotels. Even if most 
of our units are suitable for a professional use, this 
requires a separate agreement.

In accordance with our policy 
of continual product impro-
vement, we reserve the right 
to make technical and visual 
changes without notice.

For service, accessories and spare parts, please contact: 

[email protected]

Service centre: 

MAX Trader GmbH, Wilhelm-Beckmann-Straße 19, 45307 Essen, 

Germany

GUARANTEE CONDITIONS

ENVIRONMENTAL PROTECTION

At the end of its life cycle, this product must not be disposed of with household waste but must be taken 
to a collection unit for the recycling of electric and electronic equipment. The symbol on the product, 
the instructions for use or the packaging express mention of this. The basic materials can be recycled as 
specified on the labelling.
When recycling the materials and finding other utilisation for used equipment, you are making a signi-
ficant contribution towards protecting our environment. Ask at your council about the respective local 
disposal sites.

Summary of Contents for Crosstrainer Fint





















Reviews: