Sitecom 450N User Manual Download

Page: 63 / 84

E |3

Backup Settings

The Backup screen allows you to save (Backup) the router’s current

configuration settings. When you save the configuration setting (Backup) you

can re-load the saved configuration into the router through the Restore

selection. If extreme problems occur you can use the Restore to Factory

Defaults selection, this will set all configurations to its original default settings

(e.g. when you first purchased the router).

Use the "Backup" tool to save the Broadband router current configuration to a

file named "

config.bin

" on your PC. You can then use the "Restore" tool to

restore the saved configuration to the Broadband router. Alternatively, you

can use the "Restore to Factory Defaults" tool to force the Broadband router

to perform a power reset and restore the original factory settings.

Summary of Contents for 450N





















































































Search results

Summary of Contents for 450N

Reviews:

Related manuals for 450N

Brands by name

Popular brands

Sitecom 450N, User Manual

Search results

Summary of Contents for 450N

Reviews:

Related manuals for 450N

Brands by name

Popular brands