Sitecom 450N User Manual Download

Page: 4 / 84

E |3

1 Key Features

Features

Advantages

Incredible Data Rate up to

450Mbps*

Heavy data payloads such as

MPEG video streaming

IEEE 802.11n Compliant and

backwards compatible with

802.11b/g

Fully Interoperable with IEEE

802.11b / IEEE802.11g

compliant devices with legacy

protection

Four 10/100/1000 Mbps gigabit

Switch Ports (Auto-Crossover)

Scalability, extend your network.

Firewall supports Virtual Server

Mapping, DMZ, IP Filter, ICMP

Blocking, SPI

Avoids the attacks of Hackers or

Viruses from Internet

Support 802.1x authenticator,

802.11i (WPA/WPA2, AES), VPN

pass-through

Provide mutual authentication

(Client and dynamic encryption

keys to enhance security

WDS (Wireless Distribution System)

Make wireless AP and Bridge

mode simultaneously as a

wireless repeater

Sitecom Cloud Security

Protect your home against

cybercrime while browsing.

* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual

throughput may vary. Network conditions and environmental factors lower actual throughput rate.

All specifications are subject to change without notice.

Summary of Contents for 450N





















































































Search results

Summary of Contents for 450N

Reviews:

Related manuals for 450N

Brands by name

Popular brands

Sitecom 450N, User Manual

Search results

Summary of Contents for 450N

Reviews:

Related manuals for 450N

Brands by name

Popular brands