OUTPUT GRAPHICS
TRANSFERRING THE PARAMETERS FROM ENDAKEY TO DEVICE
While in "Running Mode", if key is pressed on device, “
uL
” message
appears on display and key is pressed again, parameters are read and
transferred to the device. If process succes, “
5uc
” message appears. In case
of failure, "
Err
" message displayed and parameters will not be changed on
device.
TRANSFERRING THE PARAMETERS FROM DEVICE TO ENDAKEY
NOTE 1 :
No power-up required for transfering the parameter by using
"ENDAKEY". For long battery life, "ENDAKEY" must be disconnected from
device after the transferring process.
NOTE 2 :
Please specify at order “ENDAKEY” if required.
Read
button
While in "Running Mode", if key on device or “Read” button on “ENDAKEY”
is pressed, “
dL
” message appears on display. While "
dL
" message
displayed on device and if key is pressed, parameter values from
"ENDAKEY” transferred to the device. If the parameter transfer is successful,
the "
rEf
" message appears and the device begins to work with the loaded
parameter values. If the parameters are wrong, incorrect or " ENDAKEY " is
failure, "
Err
" message appears and parameters will not be changed on
device.
HEAT
(Temperature)
output
ROTATION
INDICATOR
LED
Power
r.int
r.dur
SET
SET+
r.HYS
SET-
r.HYS
HE
control
(heating)
Rotation
mod
e
Humidification
Mode
The time between two consecutive rotating operations
Rotation duration (If
r.dur
=
0
is selecled, automatic and manual rotating is disabled.)
ROTATION
OUTPUT
h.int
h.dur
Time between two consecutive humidifications
Humidification duration (If
h.dur
=
0
is selected, humidification is disabled.)
ROTATION (CYCLE) OUTPUT GRAPHICS
HUMIDIFICATION OUTPUT GRAPHICS
HEATING OUTPUT GRAPHICS
Rotation
mod
e
HUMIDIFICATION
INDICATOR
LED
HUMIDIFICATION
OUTPUT
LoL
uPL
-60.0
°C
-60
uPL
LoL
150.0
°C
150
HY5
oFF
20.0
°C
2
20.0
°C
0
0.1
-20.0
Min.
Max.
UNIT
DEFAULT
VALUE
Unit
°F
°C
°C
Dpnt
YE5
YE5
No
CONFIGURATION PARAMETERS
Upper limit for setpoint
Heating differential (hysteresis)
Offset value for heating
CONTROL PARAMETERS
Lower limit for setpoint
Temperature unit
Decimal point (
no
= decimal point isn’t shown
22
°
C,
YE5
=decimal point is shown
22.3
°
C.)
r.dur
r.int
99:00
99:00
min:sec
0:00
ROTATION CONTROL PARAMETERS
Rotating duration ( If
r.dur
=
0
selected, automatic and manual rotation is disabled ).
Time between 2 consecutive rotation.
1:00
1:00
hr:min
0:00
h.dur
h.int
99:00
99:00
min:sec
0:00
HUMIDIFICATION CONTROL PARAMETERS
Humidification duration ( If
h.dur
=
0
selected, automatic and manual humidification is disabled ).
Time between 2 consecutive humidification.
1:00
1:00
hr:min
0:00
3
/3
ET2413K-
EN
-01-17032
7
ENDA
TM
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah.
Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:18