background image

15. 

為使機器能正常操作以及減少噪音,

機台務必平放地上,機器避免在強烈
噪音的環境下操作。

16. 

選用適當的電源插頭,並由電子技師

將其安裝在機器上,且插頭必須插在
接地線之插座上。

17. 

機器只允許被使用於指定用途上,其

他用途是不允許的。

18. 

修改或變更機器必須依照安全規定及

標準,同時採取有效的安全措施或變
更機器所引起損壞之責。

19. 

警告提示以兩種符號標示:

(1) 

對操作員或服務人員之傷害危險,也

為了避免觸電之危險,請勿打開馬達
電器箱之外蓋,也不要觸摸電器箱裡
面之零件。

(2) 

必須特別注意事項

a. 

絕對不可在移動外蓋,手指保護蓋或

安全配件後,進行機器操作,以免
導致人員受傷。

b. 

為了避免被機器纏住,當機器運轉

中,您的手、頭髮及衣服,需遠離
手輪;此外這些部位周圍不可放置
任何物品,以免導致人員受傷。

  

15. In order to operate properly and to 

reduce the noise, please place the 
machine flat and level on the ground. 
Avoid operating the sewing machine 
at a noisy  surrounding.

16. Select a proper power plug and install 

it by an electrician. Please connect the 
power plug to a grounded receptacle.

17. This machine can only be used for  

the designed purpose. Other uses of 
this machine are not allowed.

18. Any modification or conversion made 

on this machine must be conformed 
with the safety standards and 
regulations.  Precaution is necessary. 
No responsibility will our company 
take for damages caused by any 
modification or conversion of this 
machine without permission.

19. Two safety warning signs are applied 

as warning signs:

(1) For the safety of operators and  

service persons, please don't open the 
cover of any electronic control boxes 
of motor or other  devices and don't 
touch any components inside to avoid 
electrical shock hazards.

(2) Always keep in mind:

a. Please never operate this machine 

without outer cover, finger guard or 
any safety device to avoid physical 
injury.

b. Please keep your hair, fingers and 

clothes away from the hand wheel 
while the machine is in operation, 
as well as never put anything near 
these parts, to prevent the risk of 
injuries by tangled into them. 

P5

Summary of Contents for 700KS-LFD6-K1

















































Reviews: