6
SAFETY INSTRUCTIONS….cont
CAUTION:
The warnings and cautions mentioned in this user manual can not cover all possible
conditions and situations that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product, but must be applied.
When installing, please ensure your SIP submersible pump is disconnected from
the electrical supply to prevent possible injury to people and / or damage due
to un-wanted start up.
Avoid inserting hands or other objects into the inlet / outlet of the pump whilst it is
connected to the mains supply.
Use the handle provided to transport or lift the pump.
Always check the pump regularly, and take it out of service if the water is likely
to freeze.
When not in use, always ensure that the pump is fully drained of any water and
stored in a warm environment to protect it from frost damage.
Never allow the pump to run without water flowing through it.
The pump should not be used where aquatic life is present such as in a domes-
tic, or commercial pond, or similar.
Always rinse the pump with clean water and fully drain after each use.
Never carry the water pump by the mains lead or pull it to remove the plug
from the mains socket, or the pump from the water.
Keep the mains lead away from heat, oil and sharp edges.
If the mains lead is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid unwanted hazards.
Never use flammable or corrosive liquids to clean the water pump.
Never use the water pump to pump anything other than water, it should not be
used to pump flammable, corrosive or other potentially damaging or danger-
ous liquids.
The ambient temperature should be no less than 0°C.
We recommend that the pump should be switched on every 3 months for a
few minutes.
If the water pump is used in a place of work all rules and laws etc. relating to the use
of portable electrical appliances should be followed.
19
PARTS LIST
Ref No.
Description
SIP Code
Ref No.
Description
SIP Code
1.
Mains lead
PW11-00085
21.
Adjusting washer
PW11-00095
2.
Float switch
PW11-00086
22.
Impeller
PW11-00096
3.
Top cover
PW11-00087
23.
Nut M8
PW11-00071
4.
Cable protection
PW11-00053
24.
Casing
PW11-00097
5.
Cable gland
PW11-00054
25.
Steel ball
PW11-00073
6.
Capacitor
PW11-00088
26.
Gasket
PW11-00098
7.
Capacitor gland
PW11-00056
27.
Screw 2.9x8
PW11-00099
8.
Screw 3.9x30
PW11-00057
28.
Screw 4.2x32
PW11-00074
9.
Insulation plate
PW11-00058
29.
O-ring
PW11-00126
10.
Metal cover
PW11-00089
30.
Base
PW11-00100
11.
Wave washer
PW11-00060
31.
Screw 4.2x18
PW11-00077
12.
Bearing 6201
PW11-00061
32.
Bottom cover
PW11-00101
13.
Rotor
PW11-00090
33.
Screw 4.2x18
PW11-00077
14.
Bearing 6201
PW11-00061
34.
Elbow
PW11-00078
15.
Stator
PW11-00091
35.
Elbow o-ring
PW11-00079
16.
Motor lining
PW11-00092
36.
Hose adaptor
PW11-00080
17.
Motor front cover
PW11-00093
37.
Screw M4x6
PW11-00081
18.
Oil Seal 24x11x4.5
PW11-00066
38.
Spring washer M4
PW11-00082
19.
Mechanical seal
PW11-00094
39.
Earth wire
PW11-00083
20.
Main seal 89.5x5.2
PW11-00068
40.
Lock washer M4
PW11-00084
06881 SUB1015FS