18
The locking knob.
(Pic 29)
The locking knob is used to lock the required blade height and tilt positions. To loosen the locking knob turn
it counter clockwise. Before turning the table saw on, be sure that the locking knob is securely tightened so
that the blade will not shift during the table saw operation.
The riving knife.
(See Specific safety instructions for correct setting)
The riving knife ensures that when a cut is made, the two pieces of timber on either side of the blade do not
close up onto the blade. This prevents possible binding and kickback.
The rip fence.
(Pic 30)
The rip fence is used to guide the material when making long cuts, usually cutting along the grain
NEVER
rip freehand without the fence in place and securely locked.
The mitre gauge.
(Pic 31)
The mitre gauge is typically used to guide the work piece when cross cutting (across the grain) and can be
set to cut at various angles. It can be used in either of the grooves machined in the table. Always ensure
that it is locked securely when in use.
Cross cutting.
(Pic 32)
Cross cutting is cutting wood across the grain at 90° or square with both the edge and the flat side of the
wood.
Mitre cross cutting.
(Pic 33)
Mitre crosscutting is cutting the wood at an angle other than 90° with the edge of the wood. Follow the
same procedures as you would for crosscutting. But adjust the mitre gauge to the desired angle.
Bevel cross cutting.
(Pic 34)
Bevel cross cutting is the same as cross cutting except that the wood is also cut at an angle other than at
90° with the flat side of the wood. Follow the same procedures as you would for cross cutting. But adjust
the blade to the desired angle. Use the mitre gauge in the groove to the right of the blade to avoid the blade
guard from interfering with the cut.
WARNING!
When cross cutting, mitre cutting, bevel cutting and when rebating across the end of a narrow work piece
always use the mitre gauge. NEVER make these cuts freehand (not using the mitre gauge or the other de-
vices) because the blade could bind causing a kickback or causing your hand or fingers to contact the blade.
ALWAYS
lock the mitre gauge when in use. Remove the rip fence from the table when not in use.
make sure the blade safety guard is mounted for all through sawing operations (the blade cuts through the
entire thickness of the work piece). The blade should extend approximately 3.5mm (1/ 8") above the top of
the work piece.
Compound mitre cutting.
(Pic 35) Compound mitre cutting is a combination of mitre cutting and bevel
cross cutting.
The cut is made at an angle other than 90° to both the edge and the flat side of the wood.
Adjust the mitre gauge and the blade to the desired angle and be sure that the mitre gauge is locked.
Repetitive cutting.
(Pic 36)
Repetitive cutting is cutting a number of pieces the same length, without having to mark each piece. The
safe way to perform repetitive cutting, is to set the rip fence to give the required length, and to be dear of
the front of the blade (Pic 36). When the cut is made, the end of the work piece is dear of the rip fence but
at the required length.
11
GENERAL SAFETY INSTRUCTIONS:
Before attempting to operate this machine, it is important that you read, understand and follow these instruc-
tions very carefully. They are designed for the safety of yourself and others ensuring a long and trouble free
service life from your machine.
SAFE OPERATION:
Know Your Power Tool:
It is important that you read and understand your instruction manual and any label attached to the power
tool. Learn its applications as well as its limitations and the potential hazards associated with this power tool.
Work Area:
Cluttered benches and work areas invite accidents. Workbenches should be kept tidy. Floors should be kept
clean and free from rubbish. Special care should be taken where the floor is slippery due to sawdust or wax.
Work Environment:
Do not expose your power tools to rain or use in damp or wet locations. Keep the work area well lit. Do not
use power tools in areas where there is a risk of explosion or fire from combustible materials, flammable
liquids, paint, varnish, petrol etc. flammable gases and dust of an explosive nature. As a precaution it is
recommended that you consult an expert on a suitable fire extinguisher and its use.
Guard Against Electric Shock:
Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, and refrigerators).
Beware Children and Pets:
Children and pets should be kept out of the work area. Children should not be allowed to touch or operate
machinery or touch extension cords. All power tools should be kept out of the reach of children, preferably
stored or locked in a secure cabinet or room when not in use.
Do Not Force the Power Tool:
The power tool will do a better and safer job and give you much better service if it is used at the rate for
which it was designed.
Use the right tool:
Select the right tool for the job. Do not use a tool for a job for which it was not designed. Do not force a small
tool to do the job of a heavy-duty tool. Do not use tools for purposes not intended; for example do not use a
circular saw to cut tree limbs or logs.
PERSONAL SAFETY:
Clothing
Do not wear loose clothing, jewellery or anything that could get caught in moving machinery.
Hair:
Long hair should be tied back or contained in a protective covering.
Eye Protection:
The use of safety goggles is a mandatory requirement (normal glasses are not sufficient for eye protection).
Prescription spectacles do not have safety lenses.
Ear Protection:
Ear protection is advised during periods of extended operation.
Footwear:
Where there is a risk of heavy objects damaging feet or if there is a risk of slipping on wet or slippery floors
suitable non-slip safety footwear should be worn.
Head Protection:
Where there is a risk of falling objects or hitting your head on protruding or low level obstructions a hard hat
should be worn.
