Singer Studio S18 Service Manual Download Page 42 | Manualshive

Page: 42 / 47

background image

40

Setscrews (D)

Yoke (A)

3mm (C)

Plunger (B)

1. Remove the machine base (refer to page 2).
2. Loosen the 2 setscrews (D) and adjust the

distance to 3mm (C) by moving the yoke (A).

3. Tighten the 2 setscrews (D).
4. Attach the machine base.

TO ADJUST POSITION OF SOLENOID FOR BOBBIN IDLING PREVENSION LEVER

The distance between the yoke (A) and the snap ring on the plunger (B) should be 3mm (C).

«
...
40
41
42
43
44
...
»

Summary of Contents for Studio S18
















































Reviews:

No comments

Related manuals for Studio S18

Brand: Vector Fog Pages: 10

CHARGER 2022 ABLT

Brand: NSS Pages: 16

Brand: Blastrac Pages: 59

Brand: General Pages: 20

Brand: Kärcher Pages: 16

ULTRAFEED 120931

Brand: Sailrite Pages: 24

Brand: Baby Lock Pages: 84

Brand: Duerkopp Adler Pages: 9

Sweepmaster B1500 RH

Brand: HAKO Pages: 70

Brand: Kenmore Pages: 90

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 41

KX FP205 - B/W Thermal Transfer

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 64

KX FP145 - Slim-Design Fax Machine

Brand: Panasonic Pages: 86

Brand: Panasonic Pages: 110

Brand: Panasonic Pages: 216

Brand: Panasonic Pages: 230

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands