manualshive.com logo in svg

Singer 491D, Service Manual

Share
Download
Singer 491D Service Manual Download Page 33

NUMERICAL LIST OF PARTS FOR MACHINE 491D200GA

PART NO.                      DESCRIPTION
545858          Oil Pump (centrifugal) Screen Frame 
545862          Pair of Gears Nos. 545764 and 545887 
545863          Pair of Gears Nos. 545757 and 545765 
545864          Presser Bar (hollow) 
545868          Presser Bar Lifter 
545871          Presser Bar Lifting Lever Connecting Rod 
545872          Presser Bar Lifting Lever Connecting Rod Oil 
                  Mist Retaining Disc (felt) 
545873          Presser Bar Lifting Lever Connecting Rod Swivel 
545875          Presser Bar Lifting Lever Pin 
545876          Presser Bar Guide and Pressure Regulating Thumb 
                  Screw 549363 with 545403 
545881          Rotating Hook Bobbin Case Holder Position Bracket 
545883          Rotating Hook Oil Flow Regulating Thumb Screw 
                  Spring 
545884          Rotating Hook Shaft 
545885          Rotating Hook Shaft 545884 with 505648 
545886          Rotating Hook Shaft 545885 with 545890 
545887          Rotating Hook Shaft Bevel Gear (left hand 
                  spiral) with two 504101
545890          Rotating Hook Shaft Oil Retaining Collar with 
                  two 504134 
545892          Slack Thread Regulator 
545894          Tension Releasing Lever (body) 
545898          Tension Stud 
545901          Thread Eyelet (side of arm) 
545902          Thread Take-up Lever Guard 
545908          Thread Take-up Lever Oil Guard with 545909 
545909          Oil Wick (cotton) (2) 
545909          Thread Take-up Lever Oil Guard Wick (cotton) 
545949          Feed Lifting Rock Shaft Flanged Bushing (2) 
545949          Feed Rock Shaft Flanged Bushing (back) 
545950          Rotating Hook (body) with two 549182 
545951          Rotating cock complete, Nos. 945950, 545954, 
                  545955, three 549187 and four 549186 
545954          Rotating Hook Section 
545955          Rotating Hook Thread Guard 
545983          Presser Bar Guide Bracket with 545099 
545987          Feed Bar 
545990          Rotating Hook and Rotating Hook Bobbin Case 
                  Holder complete, Nos. 545951 and 545994 
545991          Rotating Hook, Rotating Hook Bobbin Case Holder 
                  and Rotating Hook Bobbin Case complete, Nos. 
                  540770 and 545990 
545994          Rotating Hook Bobbin Case Holder 
546925          Face Plate Gasket 
546927          Thread Take-up Spring Regulator with 504047 
546928          Thread Take-up Spring Regulator 546927 with 
                  540533 and 540534 
546933          Needle Bar Bushing (lower) 540524 with 540771 
548091          Feed Rock Shaft Driving Frame Spring 
548479          Oil Pump (centrifugal)(body) Position Pin (2) 
548970          Presser Bar Lifting Lever Pin Spring 
549128          Thread Eyelet (side of arm) Screw (Spec. No. 
                  1003) 
549182 (803)    Rotating Hook Screw (2) 
549183 (850)    Feed Lifting Rock Shaft Crank (back) Clamping 
                  Screw (2) 
549183 (850)    Feed Reverse Lever Hinge Stud Crank Clamping 
                  Screw 
549183 (850)    Feed Rock Shaft Crank Clamping Screw 
549186 (806)    Rotating Hook Thread Guard Screw (4) 
549187 (803)    Rotating Hook Section Screw (3) 
549230 (805)    Arm Shaft (horizontal) Screw Plug (2) 
549288 (830)    Feed Reverse Lever Hinge Stud Crank Connecting 
                  Link Screw (2) 
549336 (825)    Thread Guard (side of arm) Screw 
549363 (819)    Presser Bar Guide and Pressure Regulating 
                  Thumb Screw 
549382          Feed Regulating Screw (Spec. No. 1050) 
549383          Feed Regulating Screw Guide Screw (Spec. No. 
                  1050) 
549384          Feed Reverse Lever Spring Screw (Spec. No. 
                  1019) 
549396          Rotating Hook Oil Flow Regulating Thumb Screw 
CAT. 1901       Needle (135 x 7 #14)

                      PARTS FOR 491D300GA MACHINE 
                  WHICH DIFFER FROM 491D200GA MACHINE
125314          Tension Spring, in place of 540682 
142061-452      Throat Plate (large needle hole) for 149057, 
                  in place of 52033-452
149057          Feed Dog, 21 teeth (22 teeth per inch), in 
                  place of 149031 

PART NO.                      DESCRIPTION
540525          Needle Bar Bushing (lower), in place of 540524 
540546          Needle Bar Bushing (lower) 540525 with 545935, 
                  in place of 546933
540685          Thread Take-up Crank, in place of 540677
540688          Thread Take-up Crank 540685 with 504118, 540661 
                  and 540662, in place of 540678 
540696          Tension complete, Nos. 32758, 99691, 125314, 
                  540672, 540683, 540684, 546928 and two 2102, 
                  in place of 540671 
540698          Needle Bar (hollow) with 504112, in place of 
                  540702 
543364          Oil Wick Holder, in place of 543363 
543366          Oil Wick Holder complete, Nos. 543364, 545051 
                  and two 545909 in place of 543365 
543?17          Thread Take-up complete, Nos. 540662, 540676, 
                  540688, 543367 and 543369, in place of 540675 
545935          Needle Bar Bushing (lower) Thread Eyelet, in 
                  place of 540771 
CAT.1901        Needle (135 x 7 #16)

                       ACCESSORIES AND ATTACHMENTS 
41400           Machine Rest Pin (wood) 
55623           Rotating Hook Bobbin (3) 
505655-001      Universal Bobbin Winder complete (include two 
                  wood screws) (purchased assembly) 
505656-001      Thread Unwinder (for two spools) complete 
                  (include three wood screws)(purchased 
                  assembly) 
540520          Machine Base and Oil Reservoir Cushion (front)
                  (with two wire nails) (2) 
540521          Machine Base and Oil Reservoir Cushion (back) 
                  (with two wire nails) (2) 
540522          Machine Hinge Connection (2) 
540523          Machine Hinge Connection Cushion (2) 
541513          Screw Driver (large) 
541514          Screw Driver (small) 
541515-001      Cloth Guide (purchased part) 
545927          Oil Can (950 cc, filled with Singer Type "C" 
                  Oil) 
548701          Screw Driver (long) 
549184-001      Cloth Guide Screw (purchased part) 
CAT.1901        Needle (135 x 7 #14) (for 491D200AA) (3) 
CAT.1901        Needle (135 x 7 #16) (for 491D300AA) (3)

                    MACHINE BASE AND OIL RESERVOIR 
540471          Machine Base and Oil Reservoir Plug (2) 
540500          Machine Base and Oil Reservoir Gasket (rubber) 
543360          Machine Base and Oil Reservoir 
545036 (819)    Machine Base and Oil Reservoir Oil Drain Plug 
                  Screw 
545064 (805)    Machine and Machine Base and Oil Reservoir 
                  Screw Hole Plug Screw
545754          Machine Base and Oil Reservoir Oil Drain Plug 
                  Screw Gasket (4) 
545925          Machine and Machine Base and Oil Reservoir 
                  Screw with Washer (for shipping purposes 
                  only)

                            KNEE LIFTER PARTS
505402          Rock Shaft Knee Arm Plate 
540686          Rock Shaft Spring (coil) 
545912          Bell Crank Plunger 
545913          Rock Shaft 
545915          Rock Shaft Crank 
545917          Rock Shaft Knee Arm 
545918          Rock Shaft Knee Arm Hub 
545921          Rock Shaft Spring 
545922          Rock Shaft Stop Dog 
545923          Rock Shaft complete, Nos. 505402, 540686, 
                  545913, 545915, 545917, 545918, 545921, 
                  545922 and 546736 
546736          Rock Shaft Spring (coil) Washer

                       AVAILABLE AT EXTRA CHARGE
12481           Feed Dog for 12482 (for heavy material sewing) 
12482-452       Throat Plate for 12481 (for heavy material 
                   sewing) 
52032-452       Throat Plate (large needle hole) for 149031 
142060-452      Throat Plate (small needle hole) for 149057 
545945          Box Wrench

Summary of Contents for 491D













































Reviews:

No comments

Brands by name

Popular brands

Load more brands