manualshive.com logo in svg

Singer 491D, Service Manual

Share
Download
Singer 491D Service Manual Download Page 32

NUMERICAL LIST OF PARTS FOR MACHINE 491D200GA

PART NO.                      DESCRIPTION
540645          Feed Rock Shaft Driving Frame complete, Nos. 
                  540635, 540636, 540639, 540642, 540644, 
                  540648, 540649, 540650, 540652, 548091, 
                  549384, two each 540655, 540656, 540657 
                  and 549288 
540648          Feed Rock Shaft Crank Connecting Rod with 
                  545181 and two 545059 
540649          Feed Rock Shaft Crank Connecting Rod Pin 
540650          Feed Rock Shaft Crank Pin 
540652          Feed Rock Shaft Driving Frame with 545264 and 
                  two 545072 
540653          Feed Rock Shaft Driving Frame Hinge Pin (back) 
540654          Feed Rock Shaft Driving Frame Hinge Pin (front) 
540655          Feed Rock Shaft Driving Link (large) (2) 
540656          Feed Rock Shaft Driving Link (small) (2) 
540657          Feed Rock Shaft Driving Link (small) Pin (2) 
540660          Needle Bar Connecting Link 
540661          Needle Bar Connecting Link 540660 with 540450 
540662          Needle Bar Connecting Link Roller Bearing 
540662          Thread Take-up Lever Roller Bearing 
540663          Needle Bar Thread Guard 
540665          Oil Flow Window 
540666          Oil Pipe 
540667          Oil Pipe complete, Nos. 540666, 545846 and 
                  545847 
540669          Presser Bar Lifting Lever with 154781 
540670          Presser Bar Lifting Lever Link 
540671          Tension complete, Nos. 32758, 99691, 540672, 
                  540682, 540683, 540684, 546928 and two 2102 
540672          Tension Releasing Disc 
540673          Tension Releasing Lever (body) 545894 with 
                  545057 and 540674
540674          Tension Releasing Lever Segment 
540676          Thread Take-up Lever with 52130 
540677          Thread Take-up Crank 
540678          Thread Take-up Crank 540677 with 504118, 540661 
                  and 540662
540681          Rotating hook Shaft Bushing (back) 
540682          Tension Spring 
540683          Tension Stud 545898 with 545493 and 545404-451
540684          Tension Releasing Pin 
540689          Feed Regulating Dial Pin 
540690          Feed Regulating Dial Stopper 
540695          Machine Pulley with two 504119
540702          Needle Bar (hollow) with 504112 
540703          Needle Bar Bushing (upper) Felt 
540706          Arm Shaft (horizontal) Flanged Bushing (back) 
540707          Arm Shaft (horizontal) Flanged Bushing (back) 
                  Oil Seal 
540708          Arm Shaft (horizontal) Flanged Bushing (back) 
                  Ring 
540714          Oil Removing Tube Retaining Spring 
540716          Rotating Hook Shaft Bushing (front) 
540718          Machine Pulley Cap 
540719          Oil Pipe Clamping Sleeve Nut 
540720          Arm Shaft (horizontal) Flanged Bushing (front) 
                  540406 with Oil Drain Tube and 540722 
540722          Arm Shaft (horizontal) Flanged Bushing (front) 
                  Oil Drain Tube Tape 
540771          Needle Bar Bushing (lower) Thread Eyelet 
540767          Rotating Hook Bobbin Case Tension Spring 
540769          Rotating Hook Bobbin Case with 540767, 
                  504086 and 504087
540770          Rotating Hook Bobbin Case complete, Nos. 
                  504032, 505351, 505356 and 540769 
543363          Oil Wick Holder 
543365          Oil Wick Holder complete, Nos. 545051, 545363 
                  and two 545909
543367          Thread Take-up Lever Link 
543368          Thread Take-up Lever Link Hinge Stud 
543369          Thread Take-up Lever Link Hinge Stud 543368 
                  with 543370 
543370          Thread Take-up Lever Link Hinge Stud Oil Wick 
                  (cotton) 
543371          Oil Removing Tube Retaining Clamp 
543416          Thread Take-up Complete, Nos. 540662, 540676, 
                  540678, 543367 and 543369 
544066          Face Plate Screw (lower) (2) (Spec. No. 1009) 
545033 (805)    Arm Screw (back) (2) 
545034 (805)    Arm Screw (front) (2) 
545036 (819)    Arm Shaft (upright) Bevel Gear (upper) Set 
                  Screw Hole Plug Screw (2)
545037 (819)    Thread Take-up Crank Clamping Screw Hole Plug 
                  Screw 
545038 (819)    Arm Shaft (horizontal) Flanged Bushing (front) 
                  Oil Tube Cap Screw
545040 (809)    Face Plate Screw (short)

PART NO.                      DESCRIPTION
545043 (819)    Feed Lifting Rock Shaft Crank (front) Clamping 
                  Screw 
545046 (819)    Feed Reverse Lever Clamping Screw 
545047 (850)    Feed Reverse Lever Hinge Stud Cap Screw 
545049 (805)    Oil Pump (centrifugal) Impeller Locking Screw 
545050 (805)    Oil Pump (centrifugal) Screen Frame Screw (3) 
545051 (850)    Oil Wick Holder Screw 
545053 (850)    Presser Bar Lifter Hinge Screw 
545054 (850)    Presser Bar Lifting Lever Hinge Screw 
545057 (819)    Tension Releasing Lever Screw 
545059 (810)    Feed Lifting Rock Shaft Crank (back) Connecting 
                  Rod Cap Screw (2) 
545059 (810)    Feed Rock Shaft Crank Connecting Rod Cap Screw 
                  (2) 
545072 (833)    Feed Rock Shaft Driving Link (small) Pin Set 
                  Screw (2) 
545099 (803)    Presser Bar Guide Bracket Clamping and Tension 
                  Releaser Screw 
545160 (809)    Feed Rock Shaft Oil Plug Screw 
545181 (803)    Feed Rock Shaft Crank Connecting Rod Pin Set 
                  Screw 
545181 (803)    Feed Rock Shaft Crank Pin Set Screw 
545239          Oil Removing Pump Bracket Set Screw (3) 
545244 (805)    Feed Reverse Lever Spring Retainer Screw 
545264 (804)    Feed Rock Shaft Driving Frame Spring Stud 
545295 (805)    Feed Regulating Plate Screw (2) 
545313 (803)    Feed and Feed Lifting Eccentric Set Screw (2) 
545340 (806)    Needle Bar Connecting Stud Clamping Screw 
545403 (819)    Presser Bar Guide and Pressure Regulating Thumb 
                  Screw Lock Nut 
545404-451      Tension Regulating Thumb Nut Lock Nut (Spec. 
                  No. 1019) 
545492          Feed Regulating Nut (Spec. No. 1050) 
545493          Tension Regulating Thumb Nut (Spec. No. 1019) 
545753          Arm Screw (front) Washer (2) 
545754          Arm Shaft (upright) Bevel Gear (upper) Set 
                  Screw Hole Plug Screw Gasket (2) 
545755          Thread Take-up Crank Clamping Screw Hole Plug 
                  Screw Gasket 
545757          Arm Shaft (horizontal) Bevel Gear with two 
                  504066 
545758          Arm Shaft (horizontal) Bushing (center) 
545761          Arm Shaft (horizontal) Flanged Bushing (front) 
                  Oil Tube 
545764          Arm Shaft (upright) Bevel Gear (lower) Right 
                  Hand Spiral with two 504101 
545765          Arm Shaft (upright) Bevel Gear (upper) Left 
                  Hand Spiral with two 504101 
545766          Arm Shaft (upright) Bushing (lower) 
545767          Arm Shaft (upright) Bushing (upper) 
545770          Arm Side Shield Wick Spring Holder 
545771          Arm Side Shield Wick
545773          Arm Top Cover Gasket 
545775          Bed Hole Plug 
545776          Bed Leg (long) 
545777          Bed Leg (short) (3) 
545788          Feed Bar Connecting Link 
545789          Feed Bar Connecting Link 545788 with 272111 and 
                  540547 
545791          Feed Bar Hinge Pin 
545799          Feed Lifting Rock Shaft Crank (back) Connecting 
                  Rod Hinge Stud 
545806          Feed Lifting Rock Shaft Collar with two 504007 
                  (2) 
545807          Feed Lifting Rock Shaft Crank (back) with two 
                  549183 
545808          Feed Lifting Rock Shaft Crank (front) with 
                  545043 
545810          Feed Lifting Rock Shaft Oil Wick (cotton) 
545812          Feed Lifting Rock Shaft Crank (back) Connecting 
                  Rod with two 545059
545825          Feed Reverse Lever Hinge Stud O-ring 
545836          Feed Rock Shaft Flanged Bushing (front) 
545837          Feed Rock Shaft Collar with two 504007 
545839          Feed Rock Shaft Oil Wick (cotton) 
545841          Needle Bar Bushing (upper) 
545845          Oil Pipe 
545846          Oil Pipe Clamping Sleeve 
545847 (805)    Oil Pipe Clamping Sleeve Nut 
545849          Oil Pipe Clamping Sleeve 
545852          Oil Pipe 545845 with 545849 and 540719 for 
                  Oiling Rotating Hook Shaft Bearing (front) 
                  540716 
545854          Oil Pump (centrifugal) 
545855          Oil Pump (centrifugal) Cover 
545856          Oil Pump (centrifugal) Impeller 
545857          Oil Pump (centrifugal) Screen

Summary of Contents for 491D













































Reviews:

No comments

Brands by name

Popular brands

Load more brands