manualshive.com logo in svg

Singer 20E910, Instruction Manual And Parts List

Share
Download
Singer 20E910 Instruction Manual And Parts List Download Page 25

22

Zigzag Sewing Machine

|

Instruction Manual and Parts List

3.22

Straight and

Zigzag Stitch

Fitting (Except

20E-910)

Figure 29

Figure 31

Figure 30

Zigzag stitch Presser Foot ‘

1

’, 

Needle Plate ‘

2

’ and Feed Dog ‘

3

’

are used for straight and zigzag 
stitching. (Figure 29)

Straight Stitch Presser Foot ‘

1

’, 

Needle Plate ‘

2

’ and Feed Dog ‘

3

’

are used for straight stitching only. 
(Figure 30)

Changing the needle plate and feed 
dog (Figure 31)

Open bed slide, then remove 
needle plate, (Use screwdriver ‘

3

’

furnished with machine for removal 
and replacement of needle plate 
and feed dog.)

Using a screwdriver ‘

2

’ remove bed 

plate ‘

1

’ and remove feed dog ‘

4

’.

To replace general purpose or 
straight stitch feed dog, fasten feed 
dog to machine temporarily and 
replace general purpose or straight 
stitch needle plate. Set feed dog 
correctly in position so that it will 
not hit the edges of feed dog slots 
in the needle plate.

Replace bed plate and press it 
firmly in place.

Caution

Switch off the 

machine.

606650(20U-109/109C/309)
606651(20U-112/112C)

606588(20U-109/109C/309)
606502(20U-112/112C)

606693

606695

606697

605652(20U-102/102C/309)
606402(20U-112/112C)

1

1

2

2

3

3

1

2

3

4

Summary of Contents for 20E910

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands