background image

4  

1 - GENERAL INSTRUCTIONS

 

This appliance can be used by children 
aged from 8 years and above and 
persons with reduced physical, sensory 
or mental capabilities or lack of 
experience and knowledge if they have 
been given supervision or instruction 
concerning use of the appliance in a 
safe way and understand the hazards 
involved. Children shall not play with the 
appliance. Cleaning and user 
maintenance shall not be made by 
children without supervision. 
Before cleaning, be sure to stop the 
operation and turn the breaker off or pull 
out the power plug. 
Otherwise, an electric shock and injury 
may be caused. 
Do not insert fingers, rods or other 
objects into the air inlet or outlet. 
When the fan is rotating at high speed, it 
will cause injury. 
Do not touch the inner parts of the 
controller. 
Do not remove the front panel.  
Some parts inside are dangerous to 
touch, otherwise a machine malfunction 
may be caused. 
Never use a flammable spray such as 
hair spray, lacquer paint near the unit, it 
may cause a fire. 
Do not remove, cover or deface any 
permanent instructions, lables, or the 
data label from either the outside of the 
unit or inside of unit panels. 
It is forbidden the use of the device to 
children and unassisted disables .  
It is forbidden to touch the device if you 
are barefoot and with wet body parts .  
It is forbidden any cleaning, before 
having disconnected the device 
positioning the system main switch on 
“off”.  
It is forbidden to pull, remove, twist the 
electric cables that come out from the 
device even if it is disconnected from the 
mains supply. 

It is forbidden to trample on the device 
and/or to put on it any type of object. 
It is forbidden to throw or spray water 
directly on the device. 
It is forbidden to insert sharpened 
objects by the air return and supply 
grilles. 
It is vorbidden to open the lids of access 
to the internal device parts, without 
having before positioned the main switch 
of the system on  “off”. 
Do not turn off the power supply. 
If the supply cord is damaged, it must be 
replaced by the manufacturer or its 
service agent or a similarly qualified 
person. 
The wiring must be performed by 
professional technicians in accordance 
with national wiring regulations. 
A disconnect device for all poles having 
a separation distance of at least 3 mm 
across all poles and that a residual 
current device (RCD) with a power 
greater than 10mA is incorporated into 
fixed wiring. 
System will stop or restart heating 
automatically.  
A continuous power supply for water 
heating is necessary, except service and 
maintenance. 
Keep this manual with the wiring 
diagram in an accessible place for the 
operator.  
Children should be supervised to ensure 
that they do not play with the unit. 
Note the unit lable data so you can 
provide them at the assistance centre in 
case of intervention (see "Unit 
identification" section)  
Provide a unit notebook that allows any 
interventions carried out on the unit to 
be noted and tracked making it easier to 
suitably note the various interventions 
and aids the search for any breakdowns.  
Water temperature over 50°C can cause 
severe burns instantly or death from 
scalds. 

USER 

Summary of Contents for SWH-190-300IRE





























































Reviews: